background image

UNDERSTANDING DEVICE CONNECTIONS AND 
BUTTONS

The  rear  and  front  panel  of  the  UBC1301-AA00  has  the  following 
connections and buttons: 

USB:

 

To connect USB devices and for FW upgrades. 

RESET:

 

Use to reset the device.  Take a small object like the end of 

a paper clip and insert it into the RESET opening.   To power cycle 
the device, hold for less than 

5

 seconds.  To reset to factory default 

settings, hold for more than

 20 

seconds.   The UBC1301-AA00 will 

reset  and  reboot. 

WARNING:

  Resetting  factory  defaults  will  erase 

ANY  and  ALL  settings  that  you  have  made  and  will  restore  the 
device to factory default settings. 

 

ETH1-ETH4:

 

Use  to  connect  to  an  Ethernet-enabled  devices  such 

as  computers,  gaming  consoles  or  a  wireless  access  point  (LAN 
switch,  router)  using  an  RJ45  Ethernet  cable.  Each  Ethernet  port 
on the back panel of the device has two LEDs to indicate its status. 

When an Ethernet device is connected to the cable modem: 

•  The 

Orange

 LED is lit when connected at 10/100 Mbps speeds. 

•  The 

Green

 LED is lit when connected at 1000 speeds (Gigabit 

Ethernet). 

•   LED  blinks  (either 

Orange

  or 

Green

)  when  data  is  passed 

between the cable modem and the connected device. 

CABLE:

 

Use  to  connect  to  the  coaxial  cable  from  your  Internet 

service provider. 

TEL1-TEL2:

 

Use to connect analog telephones to the device. 

POWER:

 

Use to connect to the power adapter.  Plug the other end 

into the wall power outlet. 

WPS:

 

Located  on  the  front  panel  of  the  device,  it  is  used  for  the 

Wi-Fi Protected Setup (WPS) method to connect a PIN-protected 
Wi-Fi  device  to  the  cable  modem.  When  a  user  pushes  the  WPS 
button or triggers WPS via Web UI, flashes for 4 minutes until PIN 
is  entered  from  the  wireless  client.  After  a  WiFi  client  attaches 
successfully, the LED remains on for 5 minutes, then turns o

.

BASIC MODEM INFORMATION

www.ubeeinteractive.com

3

UBC1301-AA00 Quick Installation Guide

Example of Cable 
RF MAC Address

00:71:CC:8E:54:C7

Firmware Version

12.2.xxxx

Compatibility

DOCSIS 3.1/3.0/2.0/1.0 certified 
Ethernet 10/100/1000 Mbps 
Wireless 802.11b/g/n/ac

Local Web 
User Interface 
Access

http://192.168.100.1 

or

 http://192.168.0.1

Modem Web Page 
Login (web user 
interface)

Login:

 user 

Password: 

Broadcom

Encryption

WPA2-PSK with AES encryption

Wireless Default 
SSID

“WIFI” plus the last 6 characters of the 
Cable Modem MAC address (in upper 
case). “-5G” is added when the 5GHz 
band is being used.

SSID Examples

2.4GHz radio with above MAC address: 

SSID = WIFI8E54C7 

5GHz radio with above MAC address: 

SSID = WIFI8E54C7-5G

WPA2-PSK 
Wireless Key

Randomly generated character string, 16 
characters in length. Found on the device 
label. 

This is your wireless password.

WPA2-PSK 
Wireless Key 
Example

HP3WZ7IHXCT6D9QS

Отзывы: