U.S. Boiler Company ALTA-120 Скачать руководство пользователя страница 41

Страница: 41 / 100

110328-02 - 6/22

ALTA

Installation, Operating & Service Instructions

Table 10-7: Recommended Piping Configuration

Gas Piping

WARNING

Explosion Hazard.

• Failure to properly pipe gas supply to boiler

could cause improper operation or leaks of

flammable gas resulting in severe personal

injury, death or substantial property damage.

• Gas supply to boiler and system must be shut

off prior to installing or servicing boiler gas

piping.

1. Gas piping must be sized to deliver adequate gas

for boiler operation. Consider the following:

A. If gas pressure in building is above 1/2 psig

(3.4 kPa), an additional gas pressure

regulator is required. If additional regulator is

used to reduce boiler inlet pressure, it must

be at least 6 to 10 ft. (1.8 to 3.0 m) upstream

of boiler.

B. Pressure drop from point of delivery to boiler.

See Table 3-4 for inlet gas pressure

requirements.

C. Existing and expected future gas using

equipment (i.e. water heater, cooking

equipment, etc.).

2. Use methods and materials in accordance

with local plumbing codes. In absence of such

requirements, follow NFPA 54/ANSI Z223.1

National Fuel Gas Code

and/or CAN/CSA B149.1

Natural Gas and Propane Installation code

. Figure

11-1 shows typical gas piping and connection to

boiler.

A. Use thread compound compatible with

liquefied petroleum gas.

B. A sediment trap must be installed upstream of

gas controls.

C. A manual shut-off valve (provided in parts

carton) must be installed within 6 ft. (1.8 m) of

boiler.

D. Support weight of gas piping

independently from boiler gas connection.

3. Boiler and its gas connection must be leak

tested before placing boiler in operation.

A. For pressure testing at equal to or less than

1/2 psig (3.4 kPa) close manual shut-off valve.

B. For pressure testing above 1/2 psig (3.4 kPa)

disconnect boiler and manual shut-off valve.

Figure 11-1: Gas Piping

Gasket

Gas Valve Adapter

(1/2" NPT)

Ground Joint Union

Manual Shutoff Valve

3" Min. Drip Leg

Cap

Direction of Gas flow

DANGER

Explosion Hazard.

Do not use matches, candles, open flames or

other ignition sources to check for leaks. Failure

to comply could result in severe personal injury,

death or substantial property damage.

C. Locate leaks using listed combustible gas

detector, a non-corrosive leak detection fluid

or other listed leak detection method. Repair

any leaks found immediately.

Содержание ALTA-120





































































































Результаты поиска

Содержание ALTA-120

Отзывы:

Похожие инструкции для ALTA-120

Бренды по названию

Популярные бренды

U.S. Boiler Company ALTA-120, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание ALTA-120

Отзывы:

Похожие инструкции для ALTA-120

Бренды по названию

Популярные бренды