U-Line UMCR114-SC01A Скачать руководство пользователя | Manualshive

Страница: 9 / 48

background image

USER GUIDE

Water Hookup

Water Hookup

PREPARE PLUMBING

The water valve uses a standard 1/4” (6.35 mm)

compression fitting. U-Line recommends using accessory
water hook up kit – part #

ULAWATERHOOKUP

. The kit

includes a 10’ (3 m) braided flexible water supply line and
a brass hose fitting.

Plumbing installation must observe all state
and local codes. All water and drain connections
MUST BE made by a licensed/qualified plumbing
contractor. Failure to follow recommendations
and instructions may result in damage and/or
harm.

Water Supply Connection

When connecting the water supply, please note the
following:

•

Before installing the unit and connecting to the cold
water supply, review the local plumbing codes.

•

The water pressure should be between a minimum of

20 and a maximum of 120 psi (138 and 827 kPa).

•

The water line MUST have a shut-off valve in the
supply line.

•

The water line should be looped into 2 coils. This

will allow the unit to be removed for cleaning and
servicing. Make certain that the tubing is not pinched
or damaged during installation.

Connect to potable water supply only.

Do not use any plastic water supply line. The line
is under pressure at all times. Plastic may crack
or rupture with age and cause damage to your
home.

Do not use tape or joint compound when
attaching a braided flexible water supply line
that includes a rubber gasket. The gasket
provides an adequate seal – other materials
could cause blockage of the valve.

Failure to follow recommendations and
instructions may result in damage and/or harm,
flooding or void the product warranty.

Use new hose set. Do not reuse old hose set.

Turn off water supply and disconnect electrical

supply to unit prior to installation.
Use caution when handling back panel. The edges

could be sharp.

Turn off water supply and disconnect electrical supply to
product prior to attempting installation.

1. Remove the back panel.

2.

Locate water

valve inlet and
connect to
valve.

3.

Break away filler feature in bushing with flat

screwdriver.

4.

Thread water line through

back panel hole (with

bushing).

Note: Orientation of hole
and location of water line
clamp may be different
depending on model.

5.

Turn on water supply and

check for leaks.

6. Reinstall back panel.

7. Loosen screw on clamp,

thread water line through
water line clamp, tighten

screw.

CAUTION

!

CAUTION

!

CAUTION

!

WARNING

!

Remove

with ﬂat

screwdriver

Water line

Clamp

9

«
...
7
8
9
10
11
...
»

Содержание UMCR114-SC01A

















































Отзывы:

Нет отзывов

Похожие инструкции для UMCR114-SC01A

Бренд: Caffitaly System Страницы: 28

Бренд: TREVIDEA Страницы: 28

Бренд: Ice-O-Matic Страницы: 2

Бренд: Faema Страницы: 28

Бренд: Cime Страницы: 32

Бренд: Saeco Страницы: 100

Бренд: Salton Страницы: 6

Бренд: FUNAI Страницы: 14

Бренд: Scarlett Страницы: 8

Бренд: Johny Страницы: 4

The Ripple Maker

Бренд: Steam Страницы: 20

Бренд: Russell Hobbs Страницы: 45

Бренд: Hamilton Beach Страницы: 72

i-Joy Cafe Ultimate

Бренд: Beem Страницы: 100

Бренд: La Pavoni Страницы: 8

Бренд: SPM Страницы: 80

Pro Line MARA X PL62X

Бренд: Lelit Страницы: 28

Бренд: West Bend Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды