background image

USER GUIDE

u-line.com

Extended Non-Use

Extended Non-Use

VACATION/HOLIDAY, PROLONGED SHUTDOWN

The following steps are recommended for periods of 
extended non-use:

1.  Remove all consumable content from the unit.

2.  Disconnect the power cord from its outlet/socket 

and leave it disconnected until the unit is returned to 
service.

3.  Turn off the water supply.

4.  If ice is on the evaporator, allow ice to thaw naturally.

5.  Clean and dry the interior of the cabinet. Ensure all 

water has been removed from the unit.

6.  Disconnect the water and drain line (if applicable) 

making sure all water is removed from the lines.

7.  The door must remain open to prevent formation of 

mold and mildew. Open door a minimum of 2” (50 
mm) to provide the necessary ventilation.

WINTERIZATION

If the unit will be exposed to temperatures of 40°F (5°C) 
or less, the steps above must be followed. In addition, 
P60 drain pumps in clear ice machines must be drained 
according to the following procedure:

1.  Remove the drain pump from the ice machine.

2.  Drain the water in the pump’s reservoir by turning the 

pump upside down and allowing the water to drain 
through the pump’s inlet and vent tube fittings.

3.  After water is drained, reinstall the drain pump and 

reattach all connections.

For questions regarding winterization, please call 
U-Line at 414.354.0300.

CAUTION

!

Damage caused by freezing temperatures is not 
covered by the warranty.

Do not put anti-freeze in your unit.

23

Содержание UHWC115

























Отзывы: