U-Line UACR015 Скачать руководство пользователя

Страница: 41 / 44

USER GUIDE

Troubleshooting - Extended 10

u-line.com

SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE •

SERVICE

REPLACING ICE MAKER ASSEMBLY (CO29F
ONLY)

1. Unplug the unit from the main power source.

2. Disconnect ice maker wire harness at plug (1).

3. Remove control capillary tube from sensing tube on ice

maker assembly (2).

4. Remove water inlet tube.

5. Remove front cover (3).

6. Advance the ejector blade to the 3 o’clock position by

turning the 5/16" hex head on the small brass gear
counterclockwise (4).

7. Remove three screws from wall of freezer housing (5).

8. Remove ice maker assembly.

9. Place new ice maker assembly into position and secure

with three screws (5).

10.Reconnect wire harness at plug.

11.Insert control capillary tube into ice maker sensing

tube.

12.Insert water inlet tube.

13.Apply Permagum

to all exit holes.

14.Install back panel.

15.Plug in unit and test.

Figure 7. Ice Maker Assembly

Содержание UACR015













































Результаты поиска

Содержание UACR015

Отзывы:

Похожие инструкции для UACR015

Бренды по названию

Популярные бренды

U-Line UACR015, Руководство пользователя и сервисное руководство

Результаты поиска

Содержание UACR015

Отзывы:

Похожие инструкции для UACR015

Бренды по названию

Популярные бренды