background image

USER GUIDE

 Troubleshooting - Extended 2

SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • 

SERVICE

REFRIGERATION SYSTEM DIAGNOSIS GUIDE

ERRORS

*All errors are logged in memory.
*Only door error is displayed on the display and has an
audible signal.
*For clear ice models, pump error is displayed via alert
light with no audible alerts.

E1:

Thermistor 1 open. Refrigerator Zone.

E2:

Thermistor 2 open. Evaporator.

E3:

Thermistor 3 open Freezer Zone.

E4:

Thermistor 4 open Ice Maker.

E5:

Thermistor 1 shorted. Refrigerator Zone.

E6:

Thermistor 2 shorted. Evaporator.

E7:

Thermistor 3 shorted.Freezer Evaporator.

E8:

Thermistor 4 shorted. Ice Maker

E9:

Door open error.

Pi:

Pump Circuit open (Does not apply to this model).

MAIN CONTROL

The main control board is very robust and is rarely the 
cause of system issues. It is important to fully diagnose 
the board for any suspected failures before attempting to 
remove the board for replacement or service. Follow the 
guidelines below to fully test and diagnose the main 
control.

Power Fault

If the unit does not (or seems to not) power on, follow the 
flow chart below to help diagnose the issue. Before 
beginning it is important to first verify the unit is not 
simply set to sabbath mode.

System 

Condition

Suction 

Pressure

Suction 

Line

Compressor 

Discharge

Condenser

Capillary 

Tube

Evaporator

Wattage

Normal

Normal

Slightly below 

room 

temperature

Very hot

Very hot

Warm

Cold

Normal

Overcharge

Higher than 

normal

Very cold -

may frost 

heavily

Slightly warm 

to hot

Hot to warm

Cool

Cold

Higher than 

normal

Undercharge

Lower than 

normal

Warm -

near room 

temperature

Hot

Warm

Warm

Extremely cold 

near inlet - 

outlet below 

room 

temperature

Lower than 

normal

Partial 

Restriction

Somewhat 

lower than 

normal -

in vacuum

Warm - 

near room 

temperature

Very  hot

Top passes warm 

lower passes 

cool (near room 

temperature due 

to liquid

Room 

temperature 

(cool) or colder

Extremely cold 

near inlet -

outlet below 

room 

temperature 

backing up

Lower than 

normal

Complete 

Restriction

In deep 

vacuum

Room 

temperature 

(cool)

Room 

temperature 

(cool)

Room 

temperature 

(cool)

Room 

temperature 

(cool)

No refrigeration Lower than 

normal

No Gas

0 PSIG to 25"

Room 

temperature 

(cool)

Cool to hot

Room 

temperature 

(cool)

Room 

temperature 

(cool)

No refrigeration Lower than 

normal

41

Содержание U-CO1224FB-00B























































Отзывы: