background image

USER GUIDE

 Troubleshooting - Extended 2

SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • 

SERVICE

TROUBLESHOOTING GUIDE.

Concern

Potential Causes

Suggested Remedy

No Display or 

Interior Lights

Unit may be in Sabbath mode

Hold 

 for 5 seconds to turn off Sabbath mode, test the door switch 

circuit

No Interior Light Light may be set to OFF

Check LED strip for power
Defective door switch

Use component testing in service mode and test light circuit,
manually test door switch

Condensation on 

exterior of unit

Is unit exposed to high humidity or high 

ambient temps?

Moisture will dissipate as ambient temperature and humidity levels fall. 

Keep exterior of unit well polished to protect surface.

No Ice 

Production

Is unit level, is the unit getting water, is 

circulation pump working?

Monitor freeze cycle to assure proper water distribution over 

evaporator. Go to component testing and turn off fill valve, level unit if 

needed.

Low Ice 

Production

Dirty evaporator, dirty condenser, faulty bin 

thermistor

Clean the evaporator using U-Line cleaner, clean the condenser coil if 

needed, check bin thermistor reading in service mode.

Ice Does Not Fall 

Off During 

Harvest

Dirty evaporator, unit not level, faulty hot gas 

valve

Clean the evaporator if needed, level unit if needed, test function of hot 

gas bypass valve using relay toggle in service mode.

Error Message in 

Digital Display

Check error log

View errors in service mode, review error and take corrective action to 

resolve.

Ice is Too Thick/

Thin

Dirty evaporator, water starvation, faulty hot 

gas valve

Clean evaporator if needed, check water supply, test harvest mode, 

adjust ice thickness.

Standing Water 

in Ice Bin

Drain hose is restricted, debris in bin drain 

hole, failed drain pump

Make sure drain hose run is as straight as possible. Remove any kinks 

or tight bends, pour 1/2 gallon of water into bin to test drain.

Poor Ice Quality

Is unit level, is the evaporator dirty?

Monitor freeze mode to watch water distribution over evaporator, level 

unit if needed, clean evaporator if needed.

43

Содержание U-CLR1215INT-00B

























































Отзывы: