U-Line U-BI98B-00A Скачать руководство пользователя

Страница: 4 / 48

USER GUIDE

Safety and Warning 1

u-line.com

SAFETY

• INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE

Safety and Warning

NOTICE

Please read all instructions before installing,
operating, or servicing the appliance.

Use this appliance for its intended purpose only and follow
these general precautions with those listed throughout this
guide:

SAFETY ALERT DEFINITIONS

Throughout this guide are safety items labeled with a
Danger, Warning or Caution based on the risk type:

DANGER

Danger means that failure to follow this safety
statement will result in severe personal injury or
death.

WARNING

Warning means that failure to follow this safety
statement could result in serious personal injury
or death.

CAUTION

Caution means that failure to follow this safety
statement may result in minor or moderate
personal injury, property or equipment damage.

Содержание U-BI98B-00A

















































Результаты поиска

Содержание U-BI98B-00A

Отзывы:

Похожие инструкции для U-BI98B-00A

Бренды по названию

Популярные бренды

U-Line U-BI98B-00A, Руководство пользователя и сервисное руководство

Результаты поиска

Содержание U-BI98B-00A

Отзывы:

Похожие инструкции для U-BI98B-00A

Бренды по названию

Популярные бренды