background image

PAGE 1 OF 12 

0421 IH-7593

DELUXE FOOT SEALER 

WITH CUTTER

1-800-295-5510

uline.com

H-7593, H-7594

TECHNICAL DATA

Types of films: LDPE, HDPE, PP, PVC, BOPP. 

IMPORTANT! Read this manual thoroughly and 
familiarize yourself with ALL controls and operating 
features. Keep this manual for future reference and 
maintenance.

The machine should be located and operated in a 
dry room with good ventilation, and away from any 

flammable materials and gases.

SETUP

The machine is ready for operation after it is plugged into 

an electrical outlet and the LED illuminates. Before operation, 

adjust the sealing time and cooling time to match the film's 

type and width by conducting a sealing test.

1.  Set bottom button (sealing time) to lowest setting  

(#1 setting). (See Figure 1)

2.  Set top button (cooling time) to lowest setting  

(#1 setting). (See Figure 1)

3.  Place film between sealing bars.

4.  Use foot pedal to close sealing head, hold down and wait 

for end of sealing cycle.

5.  When sealing is complete, the sealing bar will release.

6.  If bag is not fully sealed, increase sealing and cooling 

time by turning to higher setting and repeat steps 2-4. 

 

NOTE: The quality of the seal depends on the 
thickness of the film and its composition. Test 
sealing should always be conducted at a low 
setting. If necessary, sealing time can be increased 
in small steps. 

NOTE: To achieve the best seal, keep the handle 

down for a few seconds after the sealing operation 

is complete. This allows the seal to cool down under 
pressure and become permanent.

WARNING! Sealing at a higher temperature than 
necessary may result in premature wear of parts 
and excessive melting of packaging material.

USING THE CUTTING KNIFE

For safety reasons, the knife is secured in position by a spring. 

To cut the film, press down on the knife and move it back  
and forth.

NOTE: For best results, first press the knife head down 
in the middle of the sealed film and slide it back 

and forth. This helps prevent film breakage on the 
sides. (See Figure 2)

WARNING! To prevent injury, never operate the knife 
head when the sealing bar is open. Before using, 
always ensure that the knife is intact and positioned 
correctly.

1

2

3

4

5 6

7

8

9

10

1

2

3

4

5 6

7

8

9

10

Figure 1

Figure 2

OPERATION

Cooling Time

Sealing Time

Para Español, vea páginas 5-8.

Pour le français, consulter les pages 9-12.

Содержание H-7593













Отзывы: