background image

BI2015 — Ice Maker

02/2005

13

www.U-LineService.com

CAUTION

Plumbing installation must observe all state and local 
codes. All water connections MUST BE made by a licensed/
qualified plumbing contractor. Failure to follow 
recommendations and instructions may result in damage 
and/or harm.

WARNING

To prevent accidental electrocution, make certain 
that the floor surfaces surrounding the unit are 
dry whenever power is removed from, or applied 
to, the unit.

Water Supply Connection

When connecting the water supply, follow these 
guidelines:

• Review the local plumbing codes before you install the 

unit.

• Connect to the cold water supply.

• The water pressure should be between 20 and 120 psi.

• Install a shut-off valve in the 1/4 inch OD water supply 

line.

• Connect sufficient tubing to the unit so that tubing 

may be looped, allowing the unit to be removed for 
cleaning and servicing (see 

Figure 32

). However, make 

certain that the tubing is not pinched or damaged 
during installation.

• U-Line recommends the use of copper tubing for 

installation.

To connect to water supply:

1. Install the 1/4 inch OD copper water line from the 

main water source (see 

Figure 30

).

2. Locate the compression fitting and ferrule packed with 

the unit. Slide the compression fitting and ferrule over 
the 1/4-inch OD water supply line. Do not use thread 
sealing compound or tape. Using two wrenches, 
tighten the compression fitting on the supply line 
(see

Figure 31

).

3. Carefully bend the water 

supply line into position 
and connect the line to 
the solenoid valve (see 

Figure 32

). Avoid kinking 

the water supply line.

IMPORTANT

Normal operation creates some vibration. A water supply 
line contacting cabinet wall may cause excessive noise 
during operation or damage to the line.

4. For recessed installations, allow extra water supply line 

length to provide slack for easy removal from the 
recessed area (see 

Figure 32

). This will also safeguard 

against kinking the line. 

5. Go on to 

7 Prepare Power Supply

.

6 Prepare  Plumbing

Figure 31

Figure 30

Water

Connection

Figure 32

Содержание Echelon BI 2015


















Отзывы: