background image

USER GUIDE

Door Swing 1

u-line.com

SAFETY •

INSTALLATION & INTEGRATION

 • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE

Water Hookup

PREPARE PLUMBING

The water valve uses a standard 1/4" (6.35 mm) 
compression fitting. U-Line recommends using accessory 
water hook up kit – part # 80-54674-00. The kit includes a 
10' (3 m) braided flexible water supply line and a brass 
hose fitting. 

CAUTION

!

Plumbing installation must observe all state and 
local codes. All water and drain connections 
MUST BE made by a licensed/qualified plumbing 
contractor. Failure to follow recommendations 
and instructions may result in damage and/or 
harm.

Water Supply Connection

When connecting the water supply, please note the 
following:

• Before installing the unit and connecting to the cold 

water supply, review the local plumbing codes.

• The water pressure should be between 20 and 120 psi 

(138 and 827 kPa).

• The water line MUST have a shut-off valve in the 

supply line.

• The water line should be looped into 2 coils. This will 

allow the unit to be removed for cleaning and servicing. 
Make certain that the tubing is not pinched or damaged 
during installation.

WARNING

!

Connect to potable water supply only.

CAUTION

!

Do not use any plastic water supply line. The line 
is under pressure at all times. Plastic may crack 
or rupture with age and cause damage to your 
home.

Do not use tape or joint compound when 
attaching a braided flexible water supply line 
that includes a rubber gasket. The gasket 
provides an adequate seal – other materials 
could cause blockage of the valve.

Failure to follow recommendations and 
instructions may result in damage and/or harm, 
flooding or void the product warranty.

Use new hose set. Do not reuse old hose set.

CAUTION

!

Turn off water supply and disconnect electrical 
supply to unit prior to installation.

Use caution when handling back panel. The 
edges could be sharp.

1. Turn off water supply and disconnect electrical supply 

to product prior to attempting installation.

2. Remove the grille (plinth strip/base fascia) and access 

panel (if equipped) along with back panel.

 
 
 
 
 
 

10

Содержание BI95 ADA Height Compliant Series

















































Отзывы: