EVK-U20, EVK-U23 - User Guide
UBX-13001794 - R07
Early Production Information
Starting up
Page 5 of 21
1.2
EVK-U2x block diagram
Figure 2 shows the main interfaces and internal connections of the EVK-U2x:
SIM
card holder
(J300)
Reset
(SW303)
Power-on
(SW302)
Native USB
(J200)
LISA-U2 adapter board
LISA-U2
module
42
-pin
DIL
B2B
connector
(J101)
42
-pin
DIL
B2B
connector
(J112)
EVB-WL3
GNSS
module
GNSS adapter board
RF
USB
UART
converter
Cellular USB
(UART)
(J501)
Cellular RS232
(UART)
(J500)
RS232
UART
converter
UART
MiniUSB/DB9
switch
(SW403)
On-Board/B2B
switch
(SW401)
USB
Headset jack
(J303)
I
2
C
Main
ANT
(J501)
Codec
Step - Down
Main power switch
(SW400)
12 V
(J400)
3.8 V
VCC jumper
(J404)
LDO
GPIO2/3/4
GNSS switch
(SW304)
RxDiv
ANT
(J500)
Figure 2: EVK-U2x block diagram
The EVK-U2x is formed by three boards:
The lower one, called EVB-WL3, contains the power supply and other peripherals for the LISA-U2 series
cellular module (SIM card holder, Reset button and Power-on button).
The cellular adapter board, called ADP-U200 or ADP-U230 contains the LISA-U200 or the LISA-U230 cellular
module, the antennas and USB connectors for the cellular module.
The GNSS adapter board, called ADP-GNSS, contains the u-blox GNSS module, the GNSS antenna connector
and the USB connector for the GNSS module.
The boards are connected by means of male header board-to-board connectors provided on the bottom of the
adapter boards and their corresponding female connectors provided on top of the lower board
The USB interface of the cellular module is available on the cellular native USB connector on the adapter board,
while the other peripherals are available on the Dual-In-Line male Board-to-Board connectors provided on the
top layer of the adapter board (J101, J112), which are pin-to-pin compatible to the connectors on the bottom
layer of the adapter board.
1.3
Switches, jumpers and buttons
Function
Description
Name
Board
Main Power Switch
Switch to power on / off the whole evaluation kit
SW400
EVB
Cellular VCC
Jumper socket to provide the 3.8 V supply to the cellular module VCC input
J404
EVB
Cellular Power-on
Push button to switch-on the cellular module
SW302
EVB
Cellular Reset
Push button to reset the cellular module
SW303
EVB
Cellular UART detach
Slide switch to attach / detach cellular module UART from USB and RS232 connectors:
when detached, UART signals available only on the DIL B2B connector on ADP board
SW401
EVB
Cellular UART routing
Slide switch to select cellular module UART routing on USB or on RS232 connector
SW403
EVB
Cellular GPIO detach
Slide switch to attach / detach the cellular module GPIOs, SIM_DET from peripherals:
when detached, the signals are available only on the DIL B2B connector on ADP board
SW300
EVB
Cellular GNSS detach
Slide switch to attach / detach the cellular module to the GNSS module (GPIO2-3-4):
when detached, the signals are available only on DIL B2B connector on ADP board
SW304
EVB
GNSS V_BCKP
Slide switch to connect / disconnect backup battery to V_BCKP pin of GNSS module
SW204
EVB
Table 1: EVK-U2x switches and buttons description
