4
D-306041 WK141 Installation Instructions
Panel Response
Buzzer Indication
LED Indication
Problem Indication
Success:
Operation is
successfully completed
Happy (
success
) beep
Momentary GREEN
If the panel is
Not-Ready
or if a
Trouble
or
Alarm
Memory
conditions exit, the Status button (G in Fig.1)
flashes for few seconds. To identify the reason, press
the button to retrieve the Status indication - refer to
section 3.6 for further information.
Fail:
Operation
failed
Sad (
failure
) beep
Momentary RED
No communication:
Control
panel does not respond.
None
None
3.6 Retrieving and Displaying System Status
Step
Status Request
User Actions
Keypad & Panel Response
1
Request Status
The keypad's LED blinks red once to indicate transmission of the status
request to the control panel.
2
Look at status
/
/
The panel's status is indicated on the keypad via the LED and the Arming
Keys and Partition Keys
– see below
Arming Status
The system Arming Status is indicated via the respective
arming/disarming buttons' LED
that light for several seconds. For example, if the system is
armed AWAY, the
button will light and if the system is disarmed, the
button will also light.
If Partition is enabled, the arming Status of the first partition is displayed concurrently with the corresponding first partition button LED
,
then the second
partition Status is displayed concurrently with the second partition button LED
and then the third partition Status is similarly displayed.
Indication of Ready/Not Ready & Trouble Status
The Ready/Not Ready, Alarm Memory and Trouble indications are provided via the keypad LED (see "M" in Figure 1) as follows:
LED Indication
[1]
System Status
[2]
What it Means
Green
System READY
You can arm the system
Red
System NOT- READY
One of the zones is not secured. You can not arm the system before the zone is secured or bypassed. [3]
Yellow
Trouble or Alarm Memory
There was an alarm or there is trouble situation that need to be reviewed and cleared. [3]
Yellow blinking
Keypad Low-Battery
The battery of the keypad must be replaced as shown in section 2.1.
[1]
The LED indication is displayed after the first red blink indicating the status request.
[2] If there is more than one status indication, the LED will display them consecutively.
[3] See respective sections in the control panel's User and Installer's Guides.
APPENDIX A: SPECIFICATIONS
Frequency Band (MHz)
Europe and rest of world:
433-434, 868-869
USA:
912-919**
**Note:
For UL Listed product, enable this frequency band.
Operating Temperature
0
C to 49
C (32
F to 120
F)
Dimensions (LxWxD)
127x70x24mm (5 x 2-3/4 x 31/32 in)
Communication Protocol
PowerG
Relative humidity
93%
Battery type
Battery Life Expectancy
3V, CR123A type. (GP)
4-5 years* (for typical use).
Weight (including
battery)
107g (3.4 oz)
Low Battery Threshold
2.1 V
Color
White
*
3 years+, if used with a proximity tag
APPENDIX B: COMPLIANCE WITH STANDARDS
Compliance with Standards
Europe:
EN 300220-1, EN 50130-4, EN 50131-1 Grade 2 Class II, EN 50131-3, EN 301489.
The WK141 is compatible with the RTTE requirements - Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999
and EN50131-1 Grade 2 Class II.
Certified by Norwegian accredited certification body Applica Test & Certification AS in accordance with EN 50131-3, EN 50131-6, EN
50131-5-3, EN 50130-4, and EN 50130-5.
Applica T&C has certified only the 868 MHz variant of this product.
USA:
CFR 47 part 15.
Canada
: RSS 210.
RFID Tags:
ISO-18000-2 (125 kHz)
UK:
This product is suitable for use in systems installed to conform to PD6662:2010 at Grade 2 and environmental class 2. DD243
and BS8243
The Power G peripheral devices have two- way communication functionality, providing additional benefits as described in the technical
brochure. This functionality has not been tested to comply with the respective technical requirements and should therefore be considered
outside the scope of the product’s certification.
EN 50131-1 Security Grade
According to EN 50131-1:2006 and A1:2009, this equipment can be applied in installed systems up to and including Security Grade 2.
EN 50131-1 Environmental Class
Class II
This device complies with FCC Rules Part 15 and with Industry Canada licence-exempt RSS standard(s).
This equipment complies with FCC and IC RF radiation exposure limits set forth for an uncontrolled environment.
RFID Tags:
ISO-18000-2 (125 kHz)
Operation is subject to two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference that may be received or that may cause undesired operation.
The digital circuit of this device has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in residential installations. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio and
television reception. However, there is no guarantee that interference will not occur in a particular installation. If this
device does cause such interference, which can be verified by turning the device off and on, the user is
encouraged to eliminate the interference by one or more of the following measures:
– Re-orient or re-locate the receiving antenna.
– Increase the distance between the device and the receiver.
– Connect the device to an outlet on a circuit different from the one which supplies power to the receiver.
– Consult the dealer or an experienced radio/TV technician.
Changes or modifications not expressly approved by Visonic Ltd. could void the user's authority to operate the
equipment.
WARNING
! To comply with FCC and IC RF exposure compliance requirements,
the device should be located at a distance of at least 20 cm from all persons
during normal operation. The antennas used for this product must not be co-
located or operated in conjunction with any other antenna or transmitter.
This device complies with FCC Rules Part 15 and with Industry
Canada
license-exempt RSS standard(s). Operation is subject to two conditions: (1)
This device may not cause harmful interference, and (2) this device must
accept any interference that may be received or that may cause undesired
operation
.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables
aux appareils radio exempts de licence. L'exploitation est autorisée aux deux
conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2)
l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d'en compromettre le fonctionnement.
W.E.E.E. Product Recycling Declaration
For information regarding the recycling of this product you must contact the company from which you orignially purchased it. If you are discarding this product and not
returning it for repair then you must ensure that it is returned as identified by your supplier. This product is not to be thrown away with everyday waste.
Directive 2002/96/EC Waste Electrical and Electronic Equipment.