background image

            

 

 

 

1

 

 

 

Tempest i5000XT 

///

S2696 

      Version 1.30

 

 

 

Copyright 

Copyright © TYAN Computer Corporation, 2006. All rights reserved. No part of 
this manual may be reproduced or translated without prior written consent from 
TYAN Computer Corp. 
 

Trademark 

All registered and unregistered trademarks and company names contained in 
this manual are property of their respective owners including, but not limited to 
the following. 
 
TYAN, Tempest i5000XT are trademarks of TYAN Computer Corporation. 
Intel, Greencreek, and combinations thereof are trademarks of Intel Corporation. 
Phoenix, Phoenix-Award BIOS are trademarks of Phoenix Technologies. 
 

Notice 

Information contained in this document is furnished by TYAN Computer 
Corporation and has been reviewed for accuracy and reliability prior to printing. 
TYAN assumes no liability whatsoever, and disclaims any express or implied 
warranty, relating to sale and/or use of TYAN products including liability or 
warranties relating to fitness for a particular purpose or merchantability. TYAN 
retains the right to make changes to product descriptions and/or specifications 
at any time, without notice. In no event will TYAN be held liable for any direct or 
indirect, incidental or consequential damage, loss of use, loss of data or other 
malady resulting from errors or inaccuracies of information contained in this 
document.

 

 
 

Содержание Tempest i5000XT S2696















































































Отзывы: