manualshive.com logo in svg

TYAN S2060, Руководство пользователя

Поделиться
Скачать
TYAN S2060 Скачать руководство пользователя страница 17

S2060  Tomcat i815e

17

INST

ALL

1-N.  Front Side USB Header (J18)

Certain computer chassis allow for two front-end USB port connections. This board
provides a front side USB header should you decide to
set up a USB connector at the front side of your
computer. 

Note: The front side USB header supports

a seperate channel from the rear USB ports.*

1-O. External HDD LED (J12)

Connecting J12 to an external device (i.e. SCSI card) will
result in the LED output of the device to be redirected to
the front panel HDD LED.

Soft Power Connector

The Soft Power Connector is part of jumper block J15
(pins 6-8).  The Tomcat i815e uses the chipset for power
management, including turning on and off the system.  If
the Power Button Function option in the BIOS Power
Management Menu is set to On/Off (which is the default), pressing the power button
once after the BIOS has booted up will turn the system on and off.  If the Power
Button Function option is set to Suspend, pressing the power button once will wake
the system or send it to Suspend mode.  In this case, you cannot turn the system off
unless you shut down through the Windows operating system or you hold the power
button down for four seconds.

Hardware Reset Switch Connector Installation

The Reset switch on your case’s display panel provides you with the Hardware Reset
function, which is the same as power on/off. The system will do a cold start after the
Reset button is pushed.

CMOS RTC

The Real Time Clock (RTC) circuit, which provides the date and time for the system is
integrated into the i815e chipset. If the external battery for the RTC is low, it will
prevent your system from POSTing, and you will not get a display. Normally the life
span of an external battery is 2 years. If yours is running low, you will need to replace
it with a new 3V lithium battery (Sony CR2032).

Flash EEPROM

The Tomcat i815e uses flash memory to store BIOS firmware. It can be updated as
new versions of the BIOS become available. You can upgrade your BIOS easily using
the Flash Writer Utility (see page 50).

 NOTE: Please be aware that by flashing

your BIOS, you agree that in the event of a BIOS flash failure, you must contact
your dealer for a replacement BIOS. There are no exceptions.  Tyan does not
have a policy of replacing BIOS chips directly with end users. In no event will
Tyan be held responsible for damage done to the BIOS by the end user.

!

important!

* Extra cables available at etyan: 

http://www.etyan.com

J18

J12

Содержание S2060



























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды