Twisted Hobbys Crack Turbo Beaver Скачать руководство пользователя страница 29

Страница: 29 / 34

Rev: 2013.09.15.v004a

Center of

Gravity

CG - 2.187"

from leading Edge of Wing

Locate all the electronic to achieve indicated CG point.

Use Velcro for initial flights for battery mounting and

experiment with it's position until you have

determined the best spot for your flying style. For best

3D performance a slight touch of down elevator will be

needed for inverted flight, and power off down line

should be straight down without any pull or tuck

EXTREME & 3D SET UP PRECAUTIONS

In order to achieve the control throws as suggested

above described for “Extreme & 3D”, it is

imperative that the control surface, linkages, rod

ends, etc, all move freely over the entire range,

including range end points.

Failure to do so will result in damage to either the

servos or mechanical components

Control Throws

Extreme & 3D

Ailerons - /- 40 deg

Rudder - /- 40 deg

Elevator - /- 40 deg

Expo to suit

Beginner & Sport

Ailerons - /- 20 deg

Rudder - /- 20 deg

Elevator - /- 20 deg

Expo to suit

FLAPS & SPOILERS

Spoiler Mix Settings

Flap System

Flap

Elev

Norm:

75%

Mid:

Land:

-75%

Speed:

Norm

Sw:

Flap

Mix 1

ELE > LAL

Rate:

75%

Offset:

Trim:

Inh

Sw:

FM 1

Mix 2

ELE > LAL

Rate:

-75%

Offset:

Trim:

Inh

Sw:

FM 2

Содержание Crack Turbo Beaver



































Результаты поиска

Содержание Crack Turbo Beaver

Отзывы:

Бренды по названию

Популярные бренды

Twisted Hobbys Crack Turbo Beaver, Руководство пользователя

Результаты поиска

Содержание Crack Turbo Beaver

Отзывы:

Бренды по названию

Популярные бренды