manualshive.com logo in svg

Twinno T6075, Руководство по эксплуатации

Поделиться
Скачать
Twinno T6075 Скачать руководство пользователя страница 23

21

1.LCD display is not bright

Possible causes:Instrument or LCD Screen power supply failure.
Solutions:Check whether the power supply is connected or not, and check whether the power 
supply wire of the sensor is connected in the wrong direction.

2.No current output 

Possible causes:It could be a fault in the current module or a wiring fault.
Solutions:Please check that the current output wiring is correct. Please refer to the wiring terminal 
diagram in the instructions.

3.The output current of the transmitter does not match the display current.

Possible causes:Current output may not be correctly calibrated.
Solutions:Please re-calibrate the 20mA output.

4.The instrument shows "      "

Possible causes:The transmitter and sensor are not communicating properly.
Solutions:Check that the sensor signal cable is correct. Please refer to the wiring diagram in the 
manual.

5.Measurement shows the result as full scale SLOP.

Possible causes:May be sensor was contaminated, damaged or measured value exceeds 
measurement range.
Solutions:After cleaning the sensor, put it in a medium with low concentration to observe whether 
the meter works normally. If the meter works normally, the concentration of the measured 
medium may exceed the range.

6.Measurements display results fluctuate greatly.

Possible causes:Sensor wiring error or low display rate setting.
Solutions:Check wiring or increase display rate appropriately.

FAQ

Содержание T6075



























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды