TUT FITNESS TUT TRAINER Скачать руководство пользователя страница 2

INSTALLATION 

INSTRUCTIONS

ATTENTION: PRIOR TO BEGINNING ANY FITNESS PROGRAM, PLEASE REVIEW THE INSTRUCTIONS BELOW. IF YOU ARE 
UNSURE ABOUT ANYTHING, PLEASE CONTACT CUSTOMER SERVICE [email protected] OR 
+ 1(604) 575-0259 OR TOLL FREE 1-800-674-5641

Important:  If any element/component of TUT Trainer™ appears damaged or malfunctioning, immediately

discontinue use and call Customer Service at [email protected] or +1 (604) 575-0259 or 

Toll Free 1-800-674-5641.

Important: Ensure TUT Trainer™ is locked in place. If “RED” is exposed on the lower end cap locking

pin, the TUT Trainer™ is NOT locked. DO NOT start any exercises until ensuring TUT Trainer™ is 

locked in place. Please refer to Installation Instructions Video.

ATTENTION 

ATTENTION 

ATTENTION 

Important: Ensure TUT Trainer™ chassis spring-loaded pin is set and locked firmly in place before 

commencing any exercises. DO NOT start exercising until ensuring the spring-loaded loaded pin is set, 

engaged, and locked in position. Please refer to Installation Instructions Video.

Important: Load the TUT Plates™ from the bottom first, then affix to the top. Load the TUT Plates™ 

one at a time and make sure TUT Plates™ are loaded equally on each side. Please refer to Installation

Instructions Video.

Important: When loading resistance bands (TUT Plates™) on the TUT Trainer, make sure to load the 

heaviest resistance bands on the inside (i.e.40lbs or 20lbs) and lighter resistance bands on the outside 

(i.e. 2lbs or 5lbs) Please refer to Installation Instructions Video.

Important: Ensure adjustable foot pedals on TUT Rower™ are locked firmly in place. The spring-loaded 

adjusting pins must be set, engaged, and locked firmly in place before commencing any exercises. DO 

NOT start exercising until ensuring the spring-loaded adjusting pins are set, engaged, and locked in 

position. Please refer to Installation Instructions Video.

Important: 

• Before beginning any fitness program, please consult your physician. 

• If you feel pain, faint or dizzy, stop exercising immediately. 

• Do not allow children under the age of 12 or those unfamiliar with the equipment to use it 

without supervision. 

• Do not exceed the maximum resistance load of 200 lbs. when using TUT Plates™.

• At all times, keep hands and clothing away from moving parts or joints of TUT Trainer™ and TUT Rower™ 

• Use only TUT Plates™ (TUT Fitness’ proprietary resistance bands). 

Do not use other types of resistance bands.

• Do not leave the straight bar, single handle(s) or similar attached to the rope clip when changing or 

removing resistance bands. 

• Do not leave the straight bar, single handle(s) or similar attached to the rope clip when not in use. 

ATTENTION 

DISCLAIMERS

Содержание TUT TRAINER





















Отзывы: