background image

Safety 

5816,0013US / Version 02 

17 

 

2.2 

Operator's responsibility 

The operator must comply with the statutory obligations regarding 
work safety.  
In addition to the work safety notes in these operating instructions, 
the safety, accident prevention and environmental provisions 
applicable for the area the barrier is used in must be complied with. 
In particular, the operator must: 

gather information on applicable work protection provisions.

determine additional dangers in a risk assessment.

implement the required method of operation of the barrier on
site from the operating instructions.

regularly verify throughout the barrier's time of use that the
operating instructions drawn up by him comply with the current
state of the regulations.

adapt the operating instructions to any new provisions,
standards and usage conditions - where required.

clearly determine the responsibilities for installation, operation,
maintenance and cleaning of the barrier.

ensure that all employees that are working at or with the barrier
have read and understood the operating instructions.

Furthermore, the operator must train personnel regarding the
use of the barrier at regular intervals and provide information on
possible dangers.

Furthermore, the operator is responsible for: 

keeping the barrier in perfect technical order and condition at all
times.

maintaining the barrier according to the maintenance intervals
and performing the safety inspections as stipulated.

checking all protective facilities for completeness and proper
function at regular intervals.

The operator is also responsible that the danger area of the barrier 
arm cannot be accessed by any unauthorised persons, and in 
particular not by children, under any circumstances, in systems 
used only for vehicle traffic. 

2.3  Changes and modifications 

Changes, modifications and re-builds of the barrier or installation 
can cause unforeseen danger. 
A written authorisation of the manufacturer is required before 
executing any technical changes and extensions on the barrier. 

Traffic H1 Swing Gate Horizontal Barrier

www.TURNSTILES.us | [email protected] | 303-670-1099

Содержание Traffic H1






































































































Отзывы: