Turbosound Milan M10 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 24

Turbosound Milan M10 Скачать руководство пользователя страница 4

4

Milan Series

Connection Diagrams

Small duo setup using the integrated mixer and Mix Out function

The integrated two channel mixer allows the simultaneous use of either two low impedance dynamic

microphones, a microphone and a line level source, or two line level sources. The line level source(s)

can be an acoustic instrument such as a guitar with either passive or active on-board electrics,

a keyboard, or MP3 player. Connect dynamic microphones directly to either of the combo jack/XLR

input connectors, switch the

MIC/LINE

switch to

MIC

and adjust the volume level as desired. Connect line

sources to either of the combo jack/XLR connectors, switch the

MIC/LINE

switch to

LINE

and adjust the

volume control as desired. Switch the

LOW CUT

fi lter to

'OFF'

and switch the

PROG

switch to

'MUSIC'

.

Additional microphones and sources can be connected by using the

MIX OUT

function to daisy-chain to

additional Milan loudspeakers.

«
...
2
3
4
5
6
...
»

Содержание Milan M10

























Отзывы:

Нет отзывов