manualshive.com logo in svg

Turbo Air TMW-1100E, Руководство по обслуживанию

Поделиться
Скачать
Turbo Air TMW-1100E Скачать руководство пользователя страница 25

23

(TROUBLE 4) The following visual conditions indicate a probable defective touch control circuit or membrane switch

assembly

1. Incomplete segments,

1) Segments missing.
2) Partical segments missing.
3) Digit flickering other than normal display slight flickering.
4) " :0" does not display when power is on.

2. A distinct change in the display is not on when they should be.

3. One or more digits in the display are not on when they should be.

4. Display indicates a number different from one touched.

5. Specific numbers (for example 2 or 3) will not display when the panel is touched.

6. Display does not count down or up with time cooking or clock operation.

7. Oven is programmable and cooks normally but no display shows.

8. Display obviously jumps in time while counting down.

9. Display counts down noticeable too fast while cooking.

10. Display does not show the time of day when clear pad is touched.

11. Oven lamp and turntable motor do not stop although cooking is finished. Check if the RELAY 2 contacts close if they

are close, replace touch control circuit.

NOTE 
Before following the particular steps listed above in the trouble shooting guide for the touch pad, failure, please
check for the continuity of each wire-harness between the touch pad and P.C.B. assembly.

CONDITION

CHECK

Check each control on touch

pad

Malfunction

of control circuit

board

RESULT

Normal

CAUSE

REMEDY

Replace

control circuit

board

Malfunction

of the membrane

keyboard

Abnormal

Replace the

membrane

keyboard

Display does

not show

programming

at all, even if

panel is

touched.

Содержание TMW-1100E



































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды