Tuchel Kompakt HD 400 Series Скачать руководство пользователя

Страница: 30 / 64

Attachment

. Attachment - yard loader

Before carrying out the following tasks irst read

the safety instructions in Chapter 2 - Safety.
Also, familiarise yourself with the task sequence
described.

• Check the receptacle for soiling. Clean if necessary.

• Lower the receptacle of the carrier vehicle below the

receptacle opening of the Kompakt sweeping machine.

• Insert the receptacle of the carrier vehicle into the

receptacle and lock it as described in the operating
manual of the carrier vehicle.

• Verify the correct seating of the receptacle and its lock.

• The receptacle structure must be perpendicular (1) to

the ground.

• Adjust the angle by shifting the upper hook (2). By

turning the lever (3), the upper hook is shortened or
lengthened.

• Connect the hydraulic lines, if present, according to the

instructions of the vehicle manufacturer.

• Lift the sweeping machine and carry out a functionality

check.

• Lower the sweeping machine until the two (or three)

castor wheels touch the ground.

The receptacle structure must be
perpendicular to the ground.

. Attachment to other carrier vehicles

Before carrying out the following tasks irst read

the safety instructions in Chapter 2 - Safety.
Also, familiarise yourself with the task sequence
described.

The attachment to other vehicles not described
here (wheel loader / local government vehicle)
is carried out as detailed in the carrier vehicle's
operating manual.

• Following attachment, lift the sweeping machine and

carry out a functionality check.

• Lower the sweeping machine until the two (or three)

castor wheels touch the ground.

ATTENTION

N O T E

Содержание Kompakt HD 400 Series

































































Результаты поиска

Содержание Kompakt HD 400 Series

Отзывы:

Похожие инструкции для Kompakt HD 400 Series

Бренды по названию

Популярные бренды

Tuchel Kompakt HD 400 Series, Руководство по эксплуатации

Результаты поиска

Содержание Kompakt HD 400 Series

Отзывы:

Похожие инструкции для Kompakt HD 400 Series

Бренды по названию

Популярные бренды