TubeOhm Jeannie Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 48

TubeOhm Jeannie Скачать руководство пользователя страница 6

Figure 3

Figure 3 shows how pin 1 on the IC is marked.
Either:

a:) by a dot or indentation
b:) one side of the housing is slightly bevelled.

The counting is from the left ,pin 1, to the right, pin 7 SO 14 or pin 8 SO 16.

On the PCB, pin 1 of the ICs is marked, this with a dot and also with a symbolic bevel

Soldering the SMD components-Procedure

The connections pin 1 and pin 8 (SOIC 14) or pin 1 and pin 9 (SOIC 16) are tinned on the
board. Place the IC as straight as possible on the pads and hold it firmly with your fingers.
The soldering iron tip should be cleaned of solder residue. Use the soldering iron tip to
quickly press pin 1 of the IC into the tinned pad 1 of the PCB.
Repeat the same procedure with pin 8/9. The IC is now soldered to pins 1 and 8/9 on the
board.

Figure 4

When the IC is straight, the other legs of the IC are carefully soldered on. If you use a little
soldering honey as an additional flux, the solder flows from the pads directly to the legs.

Soldering the SMD ICs is actually the most difficult part of the job.

Now let's turn to the board and get started .

6

«
...
4
5
6
7
8
...
»

Содержание Jeannie

















































Отзывы:

Нет отзывов