TTControl Vision 312 Скачать руководство пользователя страница 6

Страница: 6 / 45

1. GENERAL DESCRIPTION

≡

1 General description

1.1 Introduction

This document refers to the following products of the Vision 312 family:

• Vision 312

• Vision 312Plus

For information about the version history, please see the related Release Note document.

This User Manual is intended for qualified engineers.

1.2 Notation

In the context of this document, the term

Vision 312

(or

Vision 312

family) refers to the family and

all

its

products.

The Vision 312 products of the Vision 312 family are referred to as

Vision 312 products

The Vision 312Plus products of the Vision 312 family are referred to as

Vision 312Plus products

1.3 Advanced programming possibilities

Vision 312 runs a Linux operating system on an ARM Cortex-A9 processor. The unit can be programmed

using CODESYS. CODESYS is an IEC 61131-3 compliant development environment for application de-
velopment on a Microsoft Windows PC.

Alternatively, the unit can be programmed with C/C++ using the Linux Yocto distribution and the Qt5 frame-
work. For this purpose, a Software Development Environment (SDE) with a virtual machine is provided.

Customer applications can be downloaded via

• Ethernet

• a USB flash drive connected to the USB OTG port

• a PC connected to the USB OTG port

The device firmware is updated via a USB flash drive connected to the USB OTG port.

For the latest SW releases and the Release Note documents for the Vision 312 devices, please see our

TTControl Service Area website

https://www.ttcontrol.com/service-area/

. The Release Note documents

also contain known issues. We recommend checking the service area regularly for new SW releases and
to use the latest available SW release.

Document Number:

D-156-G-02-001

Содержание Vision 312














































Результаты поиска

Содержание Vision 312

Отзывы:

Похожие инструкции для Vision 312

Бренды по названию

Популярные бренды

TTControl Vision 312, Руководство пользователя

Результаты поиска

Содержание Vision 312

Отзывы:

Похожие инструкции для Vision 312

Бренды по названию

Популярные бренды