manualshive.com logo in svg

TSI Instruments ProCage BATTING TUNNEL FRAME KIT, Руководство по сборке

Поделиться
Скачать
TSI Instruments ProCage BATTING TUNNEL FRAME KIT Скачать руководство пользователя страница 6

STEP 

5

:  

NET INSTALLATION

1.

Stretch out batting tunnel net on ground inside frame.

2. Locate top net corners. Starting at one end, clip the net corners and center rope to cable using the snap links provided. Use 14 snap links per cable

length. Snap links should be spaced approximately 5 feet apart for a 70' net and 4 feet apart for a 55' net.
3. Use winch to lift net into place. DO NOT OVERTIGHTEN CABLE!
4. Secure each corner and center rope of tunnel net to each corner and center point of the frame.

NOTES: THE WINCH SHOULD BE SECURED BY PLACING A LOCK THROUGH ONE OF THE HOLES IN THE SIDE OF THE DRUM.  THIS WILL 

HELP PREVENT VANDALISM OR ACCIDENTAL FREE SPOOLING. 

*

MANUFACTURERS STRONGLY RECOMMEND THAT NET IS REMOVED FROM FRAME WHEN NOT USED FOR EXTENDED PERIODS OF

TIME, BEFORE HIGH WINDS, ICE OR SNOW STORMS.

*

BATTING TUNNEL FRAME IS NOT DESIGNED TO  HOLD HEAVY SNOW OR ICE LOADS.

Note: Purchaser 

 

must be responsible for compliance with any local or state building codes pertaining to this product. 

Manufacturer, distributor, or any of their representatives will assume no liability for code compliance. 

Copyright 2015 

Trigon Sports International, Inc

Page 6

Содержание ProCage BATTING TUNNEL FRAME KIT







Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды