background image

19

SERVICE INFORMATION

Contact Alnor Instrument Company before returning your Alnor Instrument
to the factory. See Instructions For Return. Follow the procedure carefully
as it will expedite processing. Failure to follow the procedure will/may cause
return of unit unrepaired. Send your instrument to the factory transportation
prepaid. To assure fast turn-around time, fill out this form with as much detail
as possible and attach it to the instrument.

Instrument Model ____________________________________________

Serial Number ______________________________________________

Date of Purchase ____________________________________________

Where Purchased ____________________________________________

Describe Malfunction ________________________________________

Describe Environment ________________________________________

Return Instrument to:

Name _____________________________________________________

(Your name or company)

Address ____________________________________________________

Telephone __________________________________________________

Address Correspondence to:

Name _____________________________________________________

Address ____________________________________________________

Telephone __________________________________________________

Содержание Alnor Velometer 6000 Series
























Отзывы: