TSC TX200 Series Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 73

background image

- 24 -

4.3 Setting Ethernet by Diagnostic Tool

The Diagnostic Utility is enclosed in the CD disk \Utilities directory. Users can use Diagnostic Tool to setup the

Ethernet by RS-232, USB and Ethernet interfaces. The following contents will instruct users how to configure the

Ethernet by these three interfaces.

4.3.1 Using USB interface to setup Ethernet interface

1. Connect the printer and computer with USB cable.

2. Turn on the printer power switch.

3. Start the Diagnostic Utility by double clicking on the

icon.

4. The Diagnostic Utility default interface setting is USB interface. If USB interface is connected with

printer, no other settings need to be changed in the interface field.

5. Click on the

“Ethernet Setup” button from “Printer Function” group in Printer Configuration tab to setup

the IP address, subnet mask and gateway for the on board Ethernet.

4.3.2 Using RS-232 interface to setup Ethernet interface

1. Connect the computer and the printer with a RS-232 cable.

«
...
31
32
33
34
35
...
»

Содержание TX200 Series










































































Отзывы:

Нет отзывов

Похожие инструкции для TX200 Series

Бренд: 3nStar Страницы: 51

Бренд: Datalogic Страницы: 24

Бренд: Datalogic Страницы: 48

Бренд: Datalogic Страницы: 36

Бренд: Datalogic Страницы: 29

Бренд: IDTECH Страницы: 8

Бренд: IDTECH Страницы: 8

Бренд: IDTECH Страницы: 12

Бренд: Hamlet Страницы: 58

Бренд: Magtek Страницы: 28

Бренд: Cansec Страницы: 14

Card Reader RCR103

Бренд: Rosewill Страницы: 3

Universal 3 in 1 Reader/Writer

Бренд: Dazzle Страницы: 47

Бренд: SAMUEL JACKSON Страницы: 11

Бренд: D'Tech Страницы: 3

Бренд: Obreey Страницы: 54

StrataScan 2755-LHR-3C

Бренд: Allen-Bradley Страницы: 68

Бренд: Anker Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды