TSC TTP 243 Pro Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 43

background image

24

TTP-243 Pro/ 243E Pro/ 342 Pro
Bar Code Printer

4.5 Ribbon Rewind Spindle Encoder Replacement

The encoder is installed on the gear box of DC motor, and is used to detect if the ribbon is
unerringly rewound by the spindle. The encoder is connected to JP37 on the mainboard.
Please switch the printer to thermal transfer mode. The multi-meter is used to measure
the voltage of Pin2 (+5V). If the voltage changes continuously from 0 to 5 volts DC, the
encoder is in condition. Otherwise, please follow the steps below to replace the encoder
PCB

1. Follow directions in Section 4.4 to remove DC motor and DC motor fixture.

DC Motor Encoder

2. Remove the two flat tap screws and cable tie.

3. Replace the Encoder PCB.

4. Reassemble the removed parts in the reverse order of removal.

«
...
25
26
27
28
29
...
»

Содержание TTP 243 Pro












































Отзывы:

Нет отзывов

Похожие инструкции для TTP 243 Pro

Code Corp CR900

Бренд: SMART-SCAN Страницы: 2

Бренд: Renkforce Страницы: 4

Бренд: TEC Страницы: 113

Бренд: StarTech.com Страницы: 11

Бренд: Unitech Страницы: 2

Бренд: Unitech Страницы: 24

303702/20190410GZ035

Бренд: APLIC Страницы: 60

Бренд: Scantech Страницы: 34

Бренд: Scantech Страницы: 40

Бренд: Scantech Страницы: 38

Бренд: Scantech Страницы: 40

Бренд: Schlumberger Страницы: 36

Бренд: Di-soric Страницы: 20

C5 Series Easy Connect

Бренд: Motion Страницы: 164

Бренд: RIOTEC Страницы: 8

Бренд: RIOTEC Страницы: 33

Бренд: RIOTEC Страницы: 5

Бренд: Datalogic Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды