TSC TC300 Series Скачать руководство пользователя страница 56 | Manualshive

Страница: 56 / 63

TSC TC300 Series Скачать руководство пользователя страница 56

51

Irregular printing

* The printer is in Hex Dump mode.
* The RS-232 setting is incorrect.

* Turn off and on the printer to skip the dump mode.
* Re-set the Rs-232 setting.

Label feeding is not stable (skew)

when printing

* The media guides do not touch the

edge of the media.

* If the label is moving to the right side, please move the

label guide to left.

* If the label is moving to the left side, please move the

label guide to right.

Skip labels when printing

* Label size is not specified properly.
* Sensor sensitivity is not set properly.
* The media sensor is covered with dust.

* Check if label size is setup correctly.
* Calibrate the sensor by Auto Gap or Manual Gap

options.

* Clear the GAP/Black mark sensor by blower.

Wrinkle Problem

* Printhead pressure is incorrect.
* Ribbon installation is incorrect.
* Media installation is incorrect.
* Print density is incorrect.
* Media feeding is incorrect.

* Please set the suitable density to have good print

quality.

* Make sure the label guides touch the edge of the media

guide.

RTC time is incorrect when reboot the

printer

* The battery has run down.

* Check if there is a battery on the main board.

The printing position of small label is

incorrect

* Media sensor sensitivity is not set

properly.

* Label size is incorrect.
* The parameter Shift Y is incorrect.
* The vertical offset setting in the driver is

incorrect.

* Calibrate the sensor sensitivity again.
* Set the correct label size and gap size.
* Use DiagTool to fine tune the parameter of Shift Y.
* If using the software BarTender, please set the vertical

offset in the driver.

«
...
54
55
56
57
58
...
»

Содержание TC300 Series
































































Отзывы:

Нет отзывов