Trumpf TruTool N 500 Скачать руководство пользователя страница 19

Страница: 19 / 22

E614EN_03.DOC

Maintenance

5.5 Regrinding the punch

3°

1 x

8°

1 x 45°

X m

3°

A Punch

(Standard)

X min. minimum length of the punch

Recommendation for the
polished section of a standard
punch for aluminum machining.

The punch can be reground, depending on the die with which it is
utilized

Note

Dies can not be resharpened.

1. Regrind the grinding surface, making sure that it is well-cooled

during the process.

2. Lightly apply fine-grained oil stone to the cutting edge.

3. Observe the minimum length (X min.) while grinding.

4. Replace shorter punches.

Punch

Die

Regrinding reserve of
the punch

Minimum length
(X min.) of the punch

5/P5

0.5 mm

58.8 mm

5/P5

2.8 mm

56.5 mm

2/3

3 -

This type of punch cannot be reground.

Fig. 52773

Table 8

Содержание TruTool N 500























Результаты поиска

Содержание TruTool N 500

Отзывы:

Похожие инструкции для TruTool N 500

Бренды по названию

Популярные бренды

Trumpf TruTool N 500, Руководство по эксплуатации

Результаты поиска

Содержание TruTool N 500

Отзывы:

Похожие инструкции для TruTool N 500

Бренды по названию

Популярные бренды