True TUI-15-L-OP-D-DSK-103-H08 Скачать руководство пользователя страница 37

Страница: 37 / 64

15” TRUE ICE

MACHINE INSTALL GUIDE

TEC_TM_155 REV. A

12/07/2021

Page 37 of 64

C A B I N E T O P E R A T I O N

E L E C T R O N I C D I S P L A Y C O D E S

Display

Definition

Detailed Description

Clean cycle reminder

In Menu Mode: view the number days elapsed since the

automatic clean cycle was performed

Drain pump failure

Clogged or kinked drain line. Drain was not able to clear

within 5 minutes of running.

Thermistor 1 Failure

Thermistor 1 is located on the evaporator outlet tube

and is used for terminating the harvest. E1 means the

probe has a bad or loose connection.

Thermistor 2 Failure

Thermistor 2 is located on the condenser outlet tube

and is used for fan cycling. E2 means the probe has a

bad or loose connection.

Fill mode

Water fills the reservoir for 2-3 minutes

Condenser coil cleaning reminder

In Menu Mode: view the number of days elapsed since

the last condenser coil cleaning.

Freeze time

In Menu Mode: view the most recent freeze times in

minutes. View history of five previous cycles:

-1 (most recent), -2, -3, -4, -5

Ice storage bin is full

Ice has reached the full level and the unit is in standby

Water level sensor

In Menu Mode: h1 is the water level reading inside the

sump tank read in mm of H2O.

Ice level sensor

In Menu Mode: h2 is the ice level reading inside the ice

storage bin in cm.

Full = 35.0 and Empty = 55.0

Harvesting ice

Ice cubes drop in the storage bin and water fills the

reservoir for the next batch of ice.

Harvest time

In Menu Mode: view the most recent harvest times in

minutes. View history of five previous cycles

-1 (most recent), -2, -3, -4, -5

Making ice

Circulation pump is running, machine sprays water into

the molds to make cubes.

High Pressure sensor

In Menu Mode: P1 is the high side pressure transducer

taken at the compressor discharge read in PSI (lb/in

)

Low Pressure sensor

In Menu Mode: P2 is the low side pressure transducer

taken at the compressor suction read in PSI (lb/in

)

Water filter reminder

In Menu Mode: view the number of days elapsed since

the last water filter replacement

Evaporator temperature

In Menu Mode: t1 is the evaporator outlet temperature

read in degrees Fahrenheit

Condenser temperature

In Menu Mode: t2 is the condenser outlet temperature

read in degrees Fahrenheit

Содержание TUI-15-L-OP-D-DSK-103-H08

































































Результаты поиска

Содержание TUI-15-L-OP-D-DSK-103-H08

Отзывы:

Похожие инструкции для TUI-15-L-OP-D-DSK-103-H08

Бренды по названию

Популярные бренды

True TUI-15-L-OP-D-DSK-103-H08, Инструкция по установке и Руководство пользователя

Результаты поиска

Содержание TUI-15-L-OP-D-DSK-103-H08

Отзывы:

Похожие инструкции для TUI-15-L-OP-D-DSK-103-H08

Бренды по названию

Популярные бренды