background image

10

www.truturf.com

RB48  Owners Manual

Assembly Procedure

Step 5: Attaching draw bar to trailer arms.

  •  Locate the draw bar assembly.

  •  Gather the ends of the right and left trailer arms.

  •  Place the draw bar assembly between the trailer 

arms and align the holes, ensure it is in the 

correct direction as per the manual drawing.

  •  Place one 2 1/2” x 3/8” bolt through each hole, 

fi

 t 

3/8” Nyloc nut to each bolt and tighten securely.

  •  Test to ensure the trailer catch is correctly locking 

the trailer arms in the down position and the 

catch locking pin 

fi

 ts correctly when transporting 

the roller, for safety.

Step 6: Attaching wheels to trailer arms.

  •   Locate the two wheels for the left and right side 

trailer arms.

  •  Check tires for the correct air pressure, 

approximately 18-24psi. Do not exceed this 

pressure. The tires act as the suspension, hence 

the low P.S.I.

  •  Remove wheel nuts from both hubs, slide wheels 

onto hub with air valves facing outwards. Replace 

wheel nuts and tighten securely.

  •  Ensure the taper on the nuts, mate into the wheel 

tapers correctly.

Step 7: Correct dampener strut operation

  •  When the roller is in the trailing position:

     1. Carefully hold the draw bar assembly.

     2.  Lower machine until the front rests on the 

ground.

     3. Release the locking catch.

     4.  Gently with a 

fi

 rm grip begin to raise the draw 

bar.

     5.  When it has travelled su

  ciently the dampener 

strut will take over and prevent the trailer arms 

rapidly rotating on it’s axle, allowing the roller 

to lower to the surface gently.

This prevents the operator from being injured.

When the roller is resting on the ground push the 

trailer arms back gently, (do not use excessive force) 

until the trailer arms will travel no further.

Содержание RB48









































Отзывы: