background image

16

TROUBLESHOOTING

If further assistance is required, contact an authorized service center.

PROBLEM

SOLUTION

The fuel tank is empty

Fill the fuel tank with fresh fuel

The primer bulb was not pressed enough

Press the primer bulb 10 times

The fuel is old (over 30 days)

Drain the fuel tank and add fresh fuel

The spark plug is fouled

Replace the spark plug

The engine is hot

Refer to the IF... THE ENGINE IS HOT instructions in the Starting 

and Stopping section

The fuel is old (over 30 days)

Drain the fuel tank and add fresh fuel

The tines are bound with dirt or grass

Stop the engine, remove the spark plug, and clean the tines

The air filter is dirty

Clean or replace the air filter

The air filter is dirty

Clean or replace the air filter

The fuel is old (over 30 days)

Drain the fuel tank and add fresh fuel

The idle speed is incorrect

Adjust the idle speed

The fuel is old (over 30 days)

Drain the fuel tank and add fresh fuel

The air filter is dirty

Clean or replace the air filter

The spark plug is fouled

Replace the spark plug

THE ENGINE WILL NOT START

THE ENGINE WILL NOT IDLE

THE ENGINE WILL NOT ACCELERATE

THE ENGINE LACKS POWER OR STALLS

Содержание TBC304









































Отзывы: