Deck Lift Lever
Found on your tractor’s right fender,
the deck lift lever is used to change
the height of the cutting deck. To
use, move the lever to the left, then
place in the notch best suited for
your application.
Ignition Switch Module
WARNING!
Never
leave a running
machine unattended.
Always disengage
PTO, set parking
brake, stop engine
and remove key to
prevent unintended
starting.
To start the engine, insert the key
into the ignition switch and turn
clockwise to the START position.
Release the key into the
NORMAL MOWING MODE
position once
the engine has fired.
To stop the engine, turn the ignition key counterclockwise to the
STOP position.
CAUTION:
Prior to operating the tractor, refer to
both Safety Interlock Switches and Starting The
Engine in the Operation section of this manual for
detailed instructions regarding the Ignition Switch
Module and operating the tractor in REVERSE
CAUTION MODE
.
Drive Pedal
The drive pedal is located on the right side
of the tractor, along the running board. Press
the drive pedal forward to cause the tractor to
travel forward. Ground speed is also controlled
with the drive pedal. The further forward that
the pedal is pivoted, the faster the tractor
will travel. The pedal will return to its original
position when it’s not pressed.
Reverse Pedal
The reverse pedal is located on the right side of
the tractor along the running board. Ground
speed is also controlled with the reverse pedal.
The further downward the pedal is pivoted,
the faster the tractor will travel. The pedal will
return to its original position when it’s not
pressed.
LCD Service Minder & Hour Meter
When the ignition key is rotated
out of the STOP position but not
into the START position, the LCD
Service Minder and Hour Meter
will briefly display the battery
voltage, followed by the tractor’s
accumulated hours.
NOTE:
Hours of tractor
operation are recorded any time
the ignition key is rotated out of
the STOP position, regardless of
whether the engine is started.
The LCD Service Minder will remind the operator of maintenance
intervals for changing the engine oil, air filter service, low engine
and low battery warnings.
Change Oil
The LCD will display the letters “CHG”, followed by the letters
“OIL”, followed by the letters “SOON”, then finally followed by the
meter’s accumulated time. “CHG/OIL/SOON/TIME” will alternate
on the display for 7 minutes after the meter reaches 50 hours.
This oil service minder interval will occur every 50 hours. Before
the interval expires, change the engine oil as instructed in the
Maintenance section of this Operator’s Manual.
Low Oil
The letters “LO” followed by the letters “OIL”, then followed by
the meter’s accumulated time will indicate the tractor is low on
oil. Stop the tractor immediately and check the engine oil level as
instructed in this Owner’s Manual.
Low Battery
At startup, the battery voltage is briefly
displayed then changes to accumulated
hours. The letters “LO” will display
followed by the letters “BATT” and then followed by the meter’s
accumulated time. “LO/BATT/TIME” is displayed on the LCD when
the voltage drops below 11.5 volts. When this occurs, the battery
is in need of a charge or the engine’s charging system is not
generating sufficient amperage. Charge the battery as instructed
in the Service section of this manual or have the charging system
checked by your local service dealer.
Air Filter Service
The letters “CLN” will display, followed by
the letters “AIR”, followed by “FILT”, then
followed by the meter’s accumulated time.
“CLN/AIR/FILT/TIME” will alternate on the
display for 7 minutes after the meter reaches 25 hours. This air
filter service minder time interval will be every 25 hours. On
intervals that are common with oil service, the oil message will
be displayed first followed by the air filter message.
13
S
ection
4 — c
ontrolS
and
F
eatureS
Содержание TB 2246
Страница 33: ...Notes 11 33...
