background image

16

Figure 23

Figure 24

9.

Reassemble new friction wheel rubber to  the 
friction wheel assembly, tightening the four screws 
in rotation and with equal force. See Figure 24. 

IMPORTANT: 

Assemble the rubber on the friction wheel 

equally for proper functioning. 

10. Insert the shift arm assembly into the friction wheel 

assembly and hold assembly in position. See 
Figure 25.

11. Slide hex shaft through right side of the housing 

and the friction wheel assembly.

12. Insert the hex shaft through the sprocket and the 

spacer. Make certain that chain engages both the 
large and the small sprocket.

NOTE: 

If the sprocket fell from the snow thrower while

removing the hex shaft, place the sprocket on the hex
shaft. Position the hex hub of the sprocket toward the
friction wheel when sliding the sprocket on to hex shaft. 

13. Align the hex shaft with the left bearing and 

carefully guide this bearing into left side of housing.

14. Install the right bearing on the hex shaft and check 

that the spacer and bearing in the drive cover are 
aligned to the steerable shaft. See Figure 25 .

15. Reassemble the drive cover with four screws 

removed in step 6. Install the right wheel with the 
bolt removed earlier.

16. Reassemble the frame cover with the two self-

tapping screws. Flip the equipment back to the 
operating position and re-attach the belt cover.

Figure 25

NOTE: 

If you placed plastic under the gas cap, be

certain to remove it. 

Adjustments

Drive Clutch 

Refer to the Final Adjustment section of the Assembly 
instructions to adjust the drive clutch. To check the 
adjustment, proceed as follows:

Drain the gasoline out of your snow thrower’s 
engine, and place a piece of plastic film under the 
gas cap to avoid spillage.

Tip the snow thrower forward, allowing it to rest on 
the auger housing.

Remove the frame cover underneath the snow 
thrower by removing self-tapping screws.

With the traction control released, check if there is 
1/8” clearance between friction wheel and drive 
plate in all positions of the shift lever. 

With the traction control lever engaged, check if the 
friction wheel solidly contacts the drive plate. See 
Figure 21. If not, adjust as follows:

Loosen the jam nut on the traction drive cable and 
thread the cable in or out as necessary.

Retighten the jam nut to secure the cable when 
correct adjustment is reached. 

17. Reassemble the frame cover.

NOTE: 

If you placed plastic under the gas cap, be

certain to remove it.

Auger Clutch 

Refer to instructions on page 6 to adjust the auger 
control.

Shift Rod 

To adjust the shift rod, proceed as follows.
1.

Place shift lever in the fastest forward speed.  See 
Figure 26A.

2.

Remove hairpin clip from the shift handle under the 
handle panel. See Figure 26B.

3.

Push shift arm assembly down as far as it will go. 

Sprocket

Bearing

Screw

Friction 

Wheel

Rubber

Plate

Friction 

Hex Shaft

Shift 
Arm

Wheel

Содержание 500 series






























Отзывы: