Troy-Bild TRACK SNOW THROWER Скачать руководство пользователя

Страница: 17 / 19

Figure 22

Figure 23

•

Position the friction wheel assembly up onto the pin
of the shift rod assembly, and slide the shaft
through the assembly. Reassemble in reverse
order.

Engine

Refer to the separate engine manual packed with your
unit.

Off-Season Storage

WARNING:

Never store the machine or

fuel container indoors where there is an open
flame, spark, or pilot light such as on water
heater, furnace, clothes dryer, or other gas
appliance.

If unit is to be stored over 30 days, prepare for storage
as instructed in the separate engine manual packed
with your snow thrower.

•

Clean snow thrower thoroughly.

•

Lubricate as instructed in the

Maintaining Your

Snow Thrower

section of this manual.

•

Store the snow thrower in a clean, dry area.

NOTE:

When storing any type of power equipment in a

poorly ventilated or metal storage shed, care should be
taken to rustproof the equipment, especially springs,
cables and all moving parts.

Track

Hex Bolt and
Cupped Washer

Shift Rod
Assembly

Sprocket

Spacer

Pin

Friction Wheel
Assembly

Shaft

Support
Bracket

Friction Wheel Rubber

Screws

Friction Wheel

Hub

Plates

Содержание TRACK SNOW THROWER




















Результаты поиска

Содержание TRACK SNOW THROWER

Отзывы:

Похожие инструкции для TRACK SNOW THROWER

Бренды по названию

Популярные бренды

Troy-Bild TRACK SNOW THROWER, Руководство оператора

Результаты поиска

Содержание TRACK SNOW THROWER

Отзывы:

Похожие инструкции для TRACK SNOW THROWER

Бренды по названию

Популярные бренды