background image

 

 

 

 

 

 

 

 

 

 

 

 

 

Suzhou Trojan Industry Material Co.

Ltd.   

 

地地址:

江苏省苏州市工业园区新泽路 53 号 A 幢 

 

电话:

0512-67580617         

传真:

0512-67508229     

 

Start  /  stop  buttons:   

Start  or  stops  the  head  in  the  manual  mode.    Note  the  Start/Stop  button  on  the  base 

polisher controls the Automatic polishing operation. 

Auto/ manual:         

Manual mode operates the head independent of the polisher. 

Auto mode operates head in conjunction with the polisher. 

Pistons Up/Down:     

UP/DOWN controls the pistons in the manual mode. 

Motor speed:               

UP/DOWN arrows for increasing or decreasing the speed. 

Head speed indicator: 

Displays the motor speed (0-200 rpm). 

Pressure adjustment:   

Controls the pressure applied to the pistons. 

 

3.2 Base Polisher Control Panel 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Wheel direction:         

Clockwise rotation or counter clockwise rotation. 

Run / stop buttons:   

Start/stop the polishing wheel in both manual and auto mode. 

Water switch:               

Activates the water solenoid for the rinse bowl and rinse spout. 

Preset speeds:           

Allows for faster speed control, SPL - low speed, SPM - medium speed, SPH - high speed. 

Auto-mode:                 

Allows for running pre-programmed speeds and times.

 

 

3.3 AUTO Polishing Mode 

1.

   

Install working wheel and attach grinding papers / polishing cloths.   

   

Position the specimen holder so that the sample tracks over the entire diameter of the grinding papers in order 
to break the grinding papers uniformly.    Note positioning is not as significant for polishing pads.   

2.   

Switch on the head and the base at the back.   

   

Set the button on the head control panel to AUTO.   

   

Set an approximate pressure and head speed on the head. 
 

3. 

Set the base speed, time and direction on the base controller (see next page for instructions) 

 
4. Position flexible water spout over working wheel.    During sample preparation adjust water flow by turning water 
control  knob  as  required.    Note:    Initial  operation  of  water  valve  may  contain  air  in  the  lines.    Turn  water  on 
slowly to purge air from system. 
 

5. 

Turn on AUTO mode so light is lit.    To start operation press START/STOP button to begin. 

Auto  mode  for  timed 
grinding/polishing 

Programming mode 

Water switch 

Preset speeds 
(Low,Meduim,High) 

Wheel direction 

Speed control 

Run/Stop 

Содержание GP 1000A














Отзывы: