8
17
10ft Maximum
Clearance Equal to Reactor for Lamp Removal
4ft Maximum
Top
Power Supply
Caution: Inspect for hidden
electrical wiring or plumbing
prior to drilling holes.
Mount on wall through
slot on back of power supply.
Further secure using slot in
bottom of ballast.
Outlet
Inlet
MODELS B & C INSTALLATION
Power Source
UV Reactor
1. To protect your power supply, you
must use a surge protector.
2. Determine location referring to
information on pages 7, 8 and 9.
3. Attach Reactor Clamp(s) to the
wall.
4. Insert Reactor and tighten
clamp(s), referring to diagram
on page 7.
5. Connect to plumbing.
6. Mount power supply to wall.
7. Attach both ground wire
(green/yellow) and strain relief
(red) to the ground stud located
beside the lamp port (outlet end).
Secure both wires with locknut
provided (see Figure 9, page 15).
8. Insert Lamp/Sleeve assembly
(see Figure 8, page 15).
9. Attach Lamp Harness to lamp
(see Figures 10, 11, 12 page 15).
10.Plug your TrojanUVMax
TM
system
into the outlet.
Note:
When the UV system is first
plugged in, the alarm may sound
temporarily until the lamp is
operational.
11.
Clean the distribution lines:
Once the UV system is installed,
any contamination in the
10ft Maximum
Clearance Equal to Reactor Length for Lamp Removal
4ft Maximum
Inlet
UV Reactor
Top
Power Supply
Caution
:
Inspect for hidden
electrical wiring or plumbing
prior to drilling holes.
Mount on wall through
slots in top and bottom
of cover.
Outlet
MODELS D, E, F, Pro7 and Pro15 INSTALLATION
Power Source
INSTALLATION
CLEANING THE QUARTZ
SLEEVE
If the water is not sufficiently
pre-treated, the quartz sleeve in
the water reactor chamber will
require periodic cleaning to remove
mineral buildup.
1. Follow the steps in Installation or
Replacement of UV Lamp/ Sleeve
section to remove the lamp/sleeve
(p.12).
2. Clean the sleeve by using a
commercial grade remover such
as Lime-A-Way
TM
or CLR
TM
on a
high-quality lint free cotton swab.
When using acidic solution
(scale remover), follow the
manufacturer’s directions for
proper use and safety. After the
lamp/sleeve is cleaned, handle it
by the ends only.
3. Follow the steps in Installation or
Replacement of UV Lamp/ Sleeve
section to install the lamp/sleeve.
Note:
Keep lamp and lamp
pins dry.
Note:
Handle lamp/sleeve at
the ends only.
Note:
If the sleeve requires
cleaning, the UV sensor will likely
require cleaning as well. Refer to
the Cleaning the UV Sensor section
for instructions.
CLEANING THE
UV SENSOR
(Plus and Pro models only)
1. Follow the steps in the UV
Intensity Monitor and
Installation Removal section to
remove the UV sensor.
2. Clean the quartz window of the
UV sensor with a commercial
scale remover (such as Lime-A-
Way
TM
or CLR
TM
) on a high-
quality lint free cotton swab.
When using acidic solution
(scale remover), follow the
manufacturer’s directions for
proper use and safety. Inspect
the window to ensure that it is
clean, clear, and dry.
3. Follow the steps in UV Sensor
Installation and Removal section
to install the UV sensor.
Note:
Do not attempt to tighten,
loosen, or open the sealed UV
sensor. Contamination of the UV
sensor or loss of function
may result.
CLEANING TIPS
You may need to use other types of
cleaners depending upon the min-
erals in your water supply. Vinegar
or isopropyl alcohol can be used
to remove grease and film on the
UV sensor, but they may not fully
remove scaling. In such cases, use
a commercial scale remover such
as Lime-A-Way
TM
or CLR
TM
. Do not
combine two or more cleaning
solutions.
Note:
If you find that you have to
clean the sensor frequently, you
should check your filters and have
your pre-treatment equipment
evaluated.
