TRIVIEW TLM-1705 Скачать руководство пользователя страница 2

 

i

P

REFACE

 

FCC Compliance Statement 

This device complies with part 15 of the FCC Rules. Operation is subjected to the 
following two conditions: 
1.  This device may not cause harmful interference, and 
2.  This device must accept any interference received, including interference that 

may cause undesired operation. 

FCC WARNING 

This equipment has been tested and found to comply with the limits for a Class B 
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to 
provide reasonable protection against harmful interference in a residential 
installation. 
This equipment generates, uses and can radiate radio frequency energy and, if 
not installed and used in accordance with the instructions, may cause harmful 
interference to radio communications. 
However, there is no guarantee that interference will not occur in a particular 
installation. If this equipment does cause harmful interference to radio or television 
reception, which can be determined by turning the equipment off and on, the user 
is encouraged to try to correct the interference by one or more of the following 
measures: 
Reorient or relocate the receiving antenna. 

• 

Increase the separation between the equipment and the receiver. 

• 

Connect the equipment into an outlet different from that to which the 
receiver is connected. 

• 

Consult the dealer or an experienced radio/TV technician for help. 

Caution: 

To comply with the limits for an FCC Class B computing device, always use the 
shielded signal cord supplied with this unit. 
The Federal Communications Commission warns that changes or modifications of 
the unit not expressly approved by the party responsible for compliance could void 
the user’s authority to operate the equipment. 

 

CE mark for Class B ITE

 

(Following European standard EN55022/1998; 

EN61000-3-2/1995; EN61000-3-3/1995, EN55024/1998, EN60950:2000+Corr. 
Feb.2002, IEC60950:1999+Corr.Jan.2000)

 

Radio Frequency Interference Statement 

Warning: 

This is a Class B product. In a domestic environment, this product may cause 
radio interference in which case the user may be required to take adequate 
measures. 

Canadian Doc Notice 

For Class B Computing Devices 

Содержание TLM-1705

















Отзывы: