TRITON Extreme
EasyStart
7.
Repeat step 5 to select and record additional tracks
Ä
Repeat step 6 to set additional Track Play Loops with
various Loop Start and Loop End settings as desired.
Tip:
Change the
“Recording Setup”
under
the
“Preference” tab to “Overdub”; go to the “Mixer1-8” tab, and you
can record Fader and Pan Automation, one Track at a time!
Tip:
Create your own User Template Song “from scratch”, or based on any Preset Song loaded: Select new
Programs on tracks, change effect bus assignments and effect programs, change mixer pan and level
settings, etc., and then save your new setup as a User Template Song (press the upper-right
▼
popup and
select “Save Template Song”).
One-Touch Recording
This great feature allows the TRITON
Extreme to capture your inspired moments whenever they happen.
The “One-Touch” record feature will instantly set the sequencer to create a new song that preserves
all
the nuances of your current playing in Program or Combination modes – Effects settings, Arpeggiator,
etc.
1.
Select any Program or Combi. (Make sure the
ARP ON/OFF
switch is already saved
ON
if you wish to
record the Arps as well) To tap in a new tempo if desired, tap the
ENTER
key
3 or more times.
2.
While holding the
ENTER
key, press the
SEQUENCER REC/START
key
Ä
Press “OK”
Ä
Press the
SEQUENCER START/STOP
key to begin the two-bar precount, and if recording arp patterns, hold down
keys on the keyboard during the precount to make sure that the patterns sync to measure 1, beat 1 at the
beginning of recording
Ä
Press the
SEQUENCER START/STOP
key when finished. All sounds, effects, and
arps have successfully been recorded in one pass! Press the
SEQUENCER START/STOP
key to playback,
and again to stop.
Note
:
To add additional tracks after recording a Combination, go to the “Preference” tab, uncheck “Multi REC” in
“Recording Setup”, and then select a new track for recording. Also, make sure to set Track Status to “INT”
(Internal) for any new Tracks that you wish to record on (MENU key > P2 Track Param/MIDI Ch T01-
08/T09-16”) If you want to overdub on an existing track, make sure to change “Over Write” to “Over Dub”
in the “Recording Setup”.
SysEx Recording
System Exclusive (SysEx) messages are used to send parameter or sample data between MIDI devices.
By recording SysEx messages in the TRITON Extreme’s sequencer, nearly any function can be adjusted
or changed as you record, and will be played back the same way! Changes to parameters such as
muting and soloing tracks, transposing a part, changing Tone-Adjust parameters and switching
arpeggiator patterns can now be recorded and saved within your sequencer data. This even includes
switching effect programs, bus assignments and parameter changes at any location in the song! You can
even use the sequencer’s Event Edit page to delete or move these Sys Ex messages.
!
To utilize SysEx Recording, make sure that “Enable Exclusive” has been selected in Global mode: Press the
GLOBAL
mode key, and then press the
MENU
key > Press “P1 MIDI” > Check the “Enable Exclusive” box.
Tone-Adjust
The Tone-Adjust function allows you to choose from 24 available “Tone-Adjust” parameters, and tweak
and edit 6 parameters for every Program assigned to a sequencer track. You no longer have to leave
Sequencer Mode to make edits so your sounds are exactly the way you want them for your Song – and
you can hear your tweaks in context with the music playing! This also leaves the original Program
unchanged in memory, so you don’t affect Combinations and other Songs.
1.
Select and load a Template Song and a few Preset drum patterns as in the previous Template Song section
Ä
Press the “Preference” tab, and then select “Over Dub” in the “Recording Setup” field
Ä
Press the
MENU
key and press “P5: Track Edit”.
5
