Tritech Merlin Скачать руководство пользователя страница 7

Страница: 7 / 32

Merlin

0711-SOM-00001, Issue: 03

© Tritech International Ltd.

2. Specification

Not to scale, dimensions in mm.

Warning

Never use the same size fitting for pressure hoses and the case drain. If this is done there

is significant risk of incorrect hook-up which will lead to pressure being applied to the motor

casing and could result in an explosion and personal injury.

Hydraulic Motor Input

Pressure 170 to 250 Bar (2450 to 3600 psi)
Flow

65 to 110 litres/min (17 to 29 USgpm)

Hydraulic Fittings

Motor A & B

No. 12 JIC male

Motor case drain

No. 6 JIC male

Actuator Connection

No. 4 JIC male

Actuator

Min. pressure

120 Bar (1740 psi)

Max. pressure

240 Bar (3480 psi)

Check Valve

Norm. Tritech Volvo Protector Assembly
Alt.

Integrated Hydraulics FPR-1/22-0.5 (cracking

pressure 0.5 bar)

Output

Typical output jetting

Up to 600 litres/min @ 8 Bar (160 USgpm @ 115 psi)

Typical output suction

2000 - 4000 litres/min (500 - 1000 USgpm)

Typical solids removal

10 - 40 tonnes/hour (350 - 1500 lb/min)

Nozzle Dimensions

Jetting

25.4mm (1")

Discharge

155mm (6")

Suction

104mm (4")

Clean water inlet

104mm (4")

Weight and Materials

Weight in air

40kg (90lb)

Weight in water

17kg (38lb)

Materials

Stainless

steel,

Nylacast,

UHMWPE

Содержание Merlin

































Результаты поиска

Содержание Merlin

Отзывы:

Похожие инструкции для Merlin

Бренды по названию

Популярные бренды

Tritech Merlin, Руководство по эксплуатации продукта

Результаты поиска

Содержание Merlin

Отзывы:

Похожие инструкции для Merlin

Бренды по названию

Популярные бренды