Tripp Lite AG-6100 Скачать руководство пользователя страница 64

Страница: 64 / 72

8. Troubleshooting

Fault and Warning events should be reviewed by authorised service personnel.

LCD Message

Explanation

Solution

Fault! Bus Over Voltage

DC bus voltage is too high.

Contact service personnel.

Fault! Bus Under Voltage

DC bus voltage is too low.

Contact service personnel.

Fault! Bus Voltage Unbalance

DC bus voltage is not balanced.

Contact service personnel.

Fault! Bus Short

DC bus is short.

Contact service personnel.

Fault! Bus Soft Start Time Out

The rectifiers could not start due to low DC bus

voltage within specified duration.

Turn off UPS and then restart the UPS.

If it fails again, contact service personnel.

Fault! Inverter Soft Start Time Out

Inverter voltage cannot reach desired voltage within

specified duration.

Turn off UPS and then restart the UPS.

If it fails again, contact service personnel.

Fault! Inverter Voltage Over

Inverter Voltage over (Peak Value).

Contact service personnel.

Fault! Inverter Voltage High

Inverter Voltage is too high.

Contact service personnel.

Fault! Inverter Voltage Low

Inverter Voltage is too Low.

Contact service personnel.

Fault! R Inverter Voltage Short

R phase inverter Output is shorted.

Contact service personnel.

Fault! S Inverter Voltage Short

S phase inverter Output is shorted.

Contact service personnel.

Fault! T Inverter Voltage Short

T phase inverter Output is shorted.

Contact service personnel.

Fault! RS Inverter Voltage Short

R-S inverter Output is shorted.

Contact service personnel.

Fault! ST Inverter Voltage Short

S-T inverter Output is shorted.

Contact service personnel.

Fault! TR Inverter Voltage Short

T-R inverter Output is shorted.

Contact service personnel.

Fault! Inverter R Negative Power

R phase inverter Output Negative Power over range. Contact service personnel.

Fault! Inverter S Negative Power

S phase inverter Output Negative Power over range. Contact service personnel.

Fault! Inverter T Negative Power

T phase inverter Output Negative Power over range. Contact service personnel.

Fault! Over Load Fault

Heavy overload causes UPS fault.

Reduce some load.

Fault! Battery Fault

Battery reverse.

Check the polarity of battery connection and
contact service personnel.

Fault! Over Temperature

Make sure adequate space is allowed for air vents
and the fan is working.

Check if the ambient temperature is over
specification or contact service personnel.

Fault! CAN Fault

CAN communication fault.

Contact service personnel.

Fault! TRIG0 Fault

Synchronised trigger signal fault.

Contact service personnel.

Fault! Relay Fault

Inverter relay fault.

Contact service personnel.

Fault! Line SCR Fail

Line SCR short circuit fault.

Contact service personnel.

Fault! EEPROM Fault

EEPROM operation error.

Contact service personnel.

Fault! Parallel Cable Loosen Fault

As stated.

Check if the parallel cable is loose and

contact service personnel.

Fault! DSP MCU Stop Communicate As stated.

Contact service personnel.

Fault! Bypass Temperature Fault

As stated.

Check if the ambient temperature is over
specification or contact service personnel.

Fault! Bypass SCR Fault

As stated.

Contact service personnel.

Warning! EPO Active

Check the EPO connector.

Check if the connector is loose when EPO
acts abnormally.

Warning! Over Load Fail

The load devices are demanding more power than
the UPS can supply. Line Mode will transfer to
Bypass Mode.

Reduce some load and check output Load-
Capacity and specification.

Warning! Communicate CAN Fail

CAN communication error.

Contact service personnel.

Warning! Over Load

When in Line Mode, the load devices are
demanding more power than the UPS can supply.

Reduce some load and check output Load-
Capacity and specification.

Warning! Battery Open

Battery not connected.

1. Check battery breaker.
2. Check if the battery connection. is well

connected.

3. Check the setting of Nominal Battery

voltage.

4. Contact service personnel if necessary.

Warning! Battery voltage High

Battery voltage is too High.

Check the setting of Nominal Battery voltage
and contact service personnel.

Warning! Turn On Abnormal

As stated.

Check if the input voltage or frequency is out
of range.

Warning! Charge Fail

As stated.

Contact service personnel.

Warning! EEPROM Fail

EEPROM operation error.

Contact service personnel.

Warning! Fan Lock

As stated.

Check if the fan is blocked or contact service
personnel.

Содержание AG-6100









































































Результаты поиска

Содержание AG-6100

Отзывы:

Похожие инструкции для AG-6100

Бренды по названию

Популярные бренды

Tripp Lite AG-6100, Руководство пользователя

Результаты поиска

Содержание AG-6100

Отзывы:

Похожие инструкции для AG-6100

Бренды по названию

Популярные бренды