Trinity ET Plus 350 Скачать руководство пользователя страница 29

Страница: 29 / 30

www.highwayguardrail.com

Revised: October 5, 2009

encountered on damaged systems.

15.

Reconstruct the systems following the installation instructions,

after the site has been cleared of damaged debris.

WARNING:

Do NOT perform installation, maintenance,

or repair if the ET-PLUS™ systems site, shoulder, or

traveled area are covered or encroached by road debris.

Failure to follow this warning could result in serious

injury or death in the event of a collision.

16.

Install proper delineation for the repaired systems in accordance

with the state/specifying agency’s MUTCD.

WARNING:

Ensure that all Guardrail products and

delineation used meet all federal, state/specifying

agency, and local specifications. Failure to follow this

warning could result in serious injury or death in the

event of a collision.

Revised: March 2010

Содержание ET Plus 350































Результаты поиска

Содержание ET Plus 350

Отзывы:

Бренды по названию

Популярные бренды

Trinity ET Plus 350, Инструкция по сборке

Результаты поиска

Содержание ET Plus 350

Отзывы:

Бренды по названию

Популярные бренды