TriMark UM 34 Скачать руководство пользователя страница 6

Страница: 6 / 13

Locking doors with keypad

Press and hold the (9/0) button for 1-2 seconds. An access code is not needed to lock the

doors

Keypad Secure Operations

Entering a valid 4-digit access code enables secure operations. After entering an access code,

the keypad is enabled for 5 seconds and a fifth button press and release initiates a secure

operation.

Notes:

•

If an unassigned button or no button is pressed while the system is enabled, the keypad

reverts to the disabled state

•

A double beep after the 4

digit indicates correct code and readiness for an output

command

Managing Keypad Access Codes

With a valid authority code (unique 6-digit code printed on keypad label) an access code can

be added or deleted with the following instructions:

1. Press the 5/6 button for 5 seconds and release 5/6 button, the keypad will beep. The

backlighting LED of the keypad will flash indicating Learn Mode is active.

2. Enter the 6-digit authority code (printed on keypad label). If the incorrect authority code

is entered, the keypad beeps for 2 seconds and exits learn mode.

3. The keypad will provide two short beeps, both LED’s blink yellow, and the backlight

flashes. The next entry indicates what function is desired.

a. 1/2 = Add access code

b. 3/4 = Delete access code

c. 7/8 (for 5 Sec) = Learn Fobs

d. 9/0 = Exit learn mode

To add a new access code

4. After the 1/2 button press, a 2 second beep indicates the code memory is full and you

need to delete codes before adding additional codes, the keypad returns to the main

learn mode (step 3 above)

5. After the 1/2 button press + double beep, enter in your new 4-digit access code. The

keypad will provide two confirmation beeps.

6. Re-enter new access code. The keypad will provide four confirmation beeps indicating

success. If the second 4-digit entry does not match the first, the keypad beeps for 2

seconds and returns to step 3 above.

7. Press 1/2 button and repeat these steps to assign additional access codes. Up to 20

unique user codes can be programmed.

Keypad 5

button

Function

(1/2)

Unlock Entry Door

(1/2) hold 2 seconds

Unlatch Entry Door

(3/4)

Unlock All

(5/6)

Unlock Luggage

Содержание UM 34














Результаты поиска

Содержание UM 34

Отзывы:

Похожие инструкции для UM 34

Бренды по названию

Популярные бренды

TriMark UM 34, Инструкция по эксплуатации

Результаты поиска

Содержание UM 34

Отзывы:

Похожие инструкции для UM 34

Бренды по названию

Популярные бренды