manualshive.com logo in svg

Trilliant SecureMesh XTEN-1000, Руководство по установке

Поделиться
Скачать
Trilliant SecureMesh XTEN-1000 Скачать руководство пользователя страница 11

SecureMesh

TM

 Extender 

 

Installation Guide 

Trilliant Incorporated 

page 11 of 21 

Connecting the Device to a Source of Power 

The Power Service Unit can be used to provide PoE power and battery backup for the Extender.  Please refer 
to the Power Service Unit Installation Guide for more information (Trilliant document PL-0042A, Installation 
Guide, SecureMesh 24V PSU).  Alternatively, the site may have its own Uninterruptible Power System that can 
be used along with a PoE injector to provide 24V power and data over an Ethernet cable; terminating in an 
8P8C connector as per TIA/EIA-568-B. 

 

Connect the Power over Ethernet (PoE) injector to the Surge Protector 

Both power and data are provided over the Ethernet cable connection to the Extender. 

Always use CAT5e (outdoor CAT5) cable that is shielded (Shielded Twisted Pair – STP), UV protected, with a 
drain-wire.  The Extender has an auto-sensing Ethernet port and therefore, either a straight through or a cross-
connect cable may be used. 

The cable seal gasket (glands) is water-tight and will not allow terminated cables to be passed through.  The 
cable will have to be re-terminated. Therefore, it may be best to perform the termination on the ground before 
beginning the installation. 

A sufficient portion of the cable shielding must be available to be connected to the ground bolt. 

•

  Run an un-terminated CAT5e cable through the open glands on the surge protector. 

•

  Strip the protective coating from the outside of the CAT5e cable to a sufficient length that the shield of the 

cable may be connected to the ground lug of the surge protector and the twisted pairs may be connected 
to the RJ45 or the connector block.  Connect the cable shield (drain wire) to the internal ground lug. 

•

  Either terminate the cable from the PoE using an RJ45 connector or terminate all eight cables to the 

terminator block.  The screw down terminator block is removable from the base board of the surge 
protector to ease connections.  Please note that the pin-outs of the RJ45 are standard 

TIA/EIA-568-B.  

The 

screw down terminal block wiring diagram is listed on the main board. 

 

 

drain wire

crimp lug 

grounding connection 
inside surge protector 

ground bolt 

unprotected 

CAT5e 

Ethernet cable 

from PoE power 

source 

wat

e

rtight glands

PoE cable 

↓

protected CAT5e 

Ethernet cable provides PoE 

power to Extender 

Содержание SecureMesh XTEN-1000






















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды