Trigon Electronics 02A00311 Скачать руководство пользователя страница 6

Страница: 6 / 12

Page 6

MINIGUARD HF-2

PROGRAMMING INFORMATION

General Programming Information

The "Initial Setup" for the HF-2 has been programmed
at the factory. These factory default settings may be
changed to better suit your particular application. If
you decide to alter these settings, follow the instructions
below. It is important that each programming step be
taken in order. When reprogramming a specific feature,
you must always enter the programming mode first. You
may then go to the appropriate procedural steps for the
changes desired.

Record below the autodialed numbers to be programmed
into the HF-2.

Autodialed Numbers

Primary Auto dial Number (16 digit max)

__ __ __ __ __ __ __ __ __ __ __ __

Second Auto dial Number (16 digit max)

__ __ __ __ __ __ __ __ __ __ __ __

Third Auto dial Number (16 digit max)

__ __ __ __ __ __ __ __ __ __ __ __

Fourth Auto dial Number (12 digit max)

__ __ __ __ __ __ __ __ __ __ __ __

Fifth Auto dial Number (16 digit max)

__ __ __ __ __ __ __ __ __ __ __ __

Sixth Auto dial Number (16 digit max)

__ __ __ __ __ __ __ __ __ __ __ __

Seventh Auto dial Number (16 digit max)

__ __ __ __ __ __ __ __ __ __ __ __

Eighth Auto dial Number (16 digit max)

__ __ __ __ __ __ __ __ __ __ __ __

Ninth Auto dial Number (16 digit max)

__ __ __ __ __ __ __ __ __ __ __ __

Tenth Auto dial Number (16 digit max)

__ __ __ __ __ __ __ __ __ __ __ __

Site ID Number-if required Number (4 digits)

__ __ __ __

PROGRAMMING

(B) Setting Operational Modes:

These settings determine how the HF-2 relays will

function.

Except when noted, each of the following program
commands will result in two (2) tones (high/low)
signifying their completion and acceptance.

Standard Mode allows the relays to be activated for a
specified time period (such as for access control
purposes).

1. Unit must be in Program Mode.

2. Press '7' then press '0' to set unit for standard
mode.

3. If desired, exit Program Mode by pressing '#'
(wait for two second tone).

4. To terminate call, press '7'.

(A) To Enter Program Mode:

1. Call the telephone number of the unit.

2. Listen for the two second tone.

3. Enter '

✽

' then the unit's Program Code.

4. If desired, exit Program Mode by pressing '#'
(wait for two second tone).

5. To terminate call, press '7'.

If the unit is new, use the preset factory code. (Factory
code is 9753).

Note: If the unit has been changed to the Emergency
Mode, use '#' instead of '

✽

' to enter program mode.

Emergency Mode, causes one relay to be momentarily
activated when a call is placed (for camera call-up) while
the other relay activates continuously throughout the
call (for lighting, etc.).

1. Unit must be in Program Mode.

2. Press '7' then press '1' to set unit for

Emergency Mode.

3. If desired, exit Program mode by pressing '#'
(wait for two second tone).

4. To terminate call, press '7'.

1. Unit must be in Program Mode.

2. Press '2' then '1' (wait for tone) and enter the
first phone number. Press '#' when complete.
Press '2' then '2' (wait for tone) and enter the
second phone number. Press '#' when complete.
If more numbers are needed press '2' then '3'
(wait for tone) and so on for up to 10 phone
numbers. Press '#' when complete.