manualshive.com logo in svg

Tridonic DALI MSensor 02, Руководство по эксплуатации продукта

Поделиться
Скачать
Tridonic DALI MSensor 02 Скачать руководство пользователя страница 29

&nbsp Extended functionality

Documentation DALI MSensor 02 | 02-2012 | en

- 29 / 38 -

Enhanced functionality

Besides Direct master mode, the DALI MSensor 02 also supports two further modes for use in combination with a

higher-level DALI master controller:

Indirect master mode

Slave mode

Ex factory, the DALI MSensor 02 is in Direct master mode. The sensor can be switched to the desired mode by using the

master controller itself or by using the masterCONFIGURATOR software.

Notice

If used in conjunction with an external system note the following:

Make sure that the DALI MSensor 02 is compatibel with the external system

Make sure that the producer of the external system has conferred the right to use the DALI MSensor

in conjunction with their own product

Indirect master mode

In Indirect master mode, the DALI MSensor 02 does not send any active control commands to the luminaires; it sends the

measured light value, presence detection status and remote control status to a higher-level master. The master controller

analyses this information and sends the corresponding control commands to the luminaires.

eDALI is used to communicate with the master. eDALI is Tridonic GmbH & Co KG's proprietary extension of the DALI

standard.

Slave mode

In Slave mode, the DALI MSensor 02 do not send any active control commands to the luminaires; it has to be interrogated by

a higher-level control system (master).

As in Direct master mode, the DALI MSensor 02 is given a DALI address during addressing. The brightness currently

measured by the sensor and the status of the presence detector can be interrogated via this DALI address by using the

"QUERY ACTUAL LEVEL" DALI request. A detailed listing and explanation of the supported DALI commands can be found

in the annex (

).

see chapter "Reaction to DALI commands sent to the DALI address", page 37

Notice

The remote control is inoperative in Slave mode.

The rotary switch at the rear of the DALI MSensor 02 is inoperative in Slave mode.

...

Содержание DALI MSensor 02







































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды