NPB-LON Option Installation Sheet
Updated: May 29, 2009
Part Number 10620 Rev. 2
Wiring
Material and Tools Required
2
3.
For
all
but
the
J
‐
202
‐
XPR,
remove
the
battery
and
bracket
assembly
by
taking
out
the
screws
holding
it
in
place,
setting
the
screws
aside
for
later.
Unplug
the
battery
from
the
connector
on
the
JACE.
See
for
an
exploded
view.
Figure 2
Remove battery assembly.
4.
Remove
the
blanking
end
plate
for
the
slot
you
are
installing
the
option
card
into.
(Retain
the
blanking
end
plate
in
case
the
option
card
must
be
removed
at
a
later
date.)
5.
Carefully
insert
the
pins
of
the
NPB
‐
LON
into
the
socket
of
the
appropriate
option
card
slot.
The
mounting
holes
on
the
option
board
should
line
up
with
the
standoffs
on
the
base
board.
If
they
do
not,
the
connector
is
not
properly
aligned.
Press
until
the
option
card
is
completely
seated.
6.
Place
the
custom
end
plate
that
came
with
the
NPB
‐
LON
over
its
connector
(see
).
Figure 3
NPB-LON inserted, end plate on top.
7.
Plug
the
battery
cable
into
the
battery
connector
on
the
JACE
shows
the
location
of
the
battery
connector
on
the
JACE
‐
200/600).
8.
For
all
but
the
J
‐
202
‐
XPR,
set
the
battery
and
bracket
assembly
back
over
the
option
card
slots,
with
mounting
holes
aligned
with
the
standoffs.
Screws
enter
holes
in
the
battery
bracket
first.
Figure 4
Re-fasten screws.
9.
Place
the
screws
through
the
end
plate(s),
and
into
the
standoffs
on
the
base
board.
Using
a
screwdriver,
hand
tighten
screws.
10.
Replace
the
JACE
cover
or
covers
(J
‐
202
‐
XPR).
If
accessory
modules
were
unplugged
from
the
JACE,
plug
them
back
as
before,
and
secure.
Wiring
Connect
LonWorks
FTT
‐
10
communications
wiring
to
the
2
position
connector
of
the
NPB
‐
LON.
Note
that
polarity
is
not
a
factor
in
FTT
‐
10
wiring.
Refer
to
the
LonWorks
FTT
‐
10A
Free
Topology
Transceiver
User’s
Guide
(078
‐
0156
‐
01F)
for
technical
guidelines
associated
with
free
topology
restrictions,
and
the
Junction
Box
and
Wiring
Guidelines
for
Twisted
Pair
LonWorks
Networks
(005
‐
0023
‐
01)
for
more
detailed
information
on
wiring
specifications.
These
documents
are
available
on
Echelon’s
web
site
(www.echelon.com).
LEDs
Two
LEDs
are
visible
on
the
top
of
the
NPB
‐
LON
option
card
(cover
must
be
removed
from
JACE):
•
RX
(green)
—
Receive,
indicates
that
another
LonWorks
device
is
transmitting
a
message.
•
TX
(yellow)
—
Transmit,
indicates
that
the
JACE
is
transmitting
a
message
on
the
LON
trunk.
These
LEDs
are
included
on
the
top
label
of
the
the
NPB
‐
LON,
see
Screws (4)
Option
Slot 2
Area
Blanking
End
Plate
Battery
Assembly
(includes
cable and
bracket)
Unplug battery here
Option
Slot 1
Area
JACE-200/600
JACE
Battery
Connector
Place NPB-LON custom
end plate over end.
Insert NPB-LON into
option card slot carefully,
with
pins aligned
.
Fully seat card.
JACE-200/600
For JACE models
with battery
assembly over the
Option Slots,
reinsert the
4 screws through
the battery bracket,
end plates, and into
the standoffs.
JACE-200/600
