3951 Westerre Parkway, Suite 350
Richmond, Virginia 23233 USA
NPB-LON Option
INSTALLATION SHEET
NPB-LON Option Installation Sheet
Part Number 10620 Rev. 2
Updated: May 29, 2009
1
Information and specifications published here are current as of the date of publication of this document. Tridium, Inc. reserves the right to change or modify
specifications without prior notice. The latest product specifications can be found by contacting our corporate headquarters, Richmond, Virginia. Products or
features contained herein may be covered by one or more U.S. or foreign patents.
© 2009 Tridium, Inc.
This
document
covers
the
mounting
and
wiring
of
the
NPB
‐
LON
1
option
card
in
a
Vykon
®
JACE
controller
(JACE
‐
200/600,
SEC
‐
J
‐
x
01,
or
J
‐
202
‐
XPR
series).
Refer
to
the
appropriate
JACE
®
mounting
and
wiring
document
for
further
JACE
installation
details.
Included in this Package
Included
in
this
package
you
should
find
the
following
items:
•
NPB
‐
LON
option
card,
connector
end
plate.
•
one
2
‐
position
terminal
plug,
for
wiring
to
an
FTT
‐
10
LonWorks
®
network
•
This
NPB
‐
LON
Option
Installation
Sheet
,
Part
Number
10620
Rev.
2
Material and Tools Required
The
following
tools
and
supplies
may
be
required
for
installation:
•
#2
phillips
screwdriver:
to
install
the
NPB
‐
LON.
•
Small
flat
‐
blade
screwdriver:
to
make
wiring
connections
to
the
FTT
‐
10
Lonworks
network.
•
#1
phillips
screwdriver:
to
remove
and
refasten
J
‐
202
‐
XPR
covers
(if
applicable).
Figure 1
NPB-LON option.
Mounting
Warning
Power
to
the
JACE
must
be
OFF
when
installing
or
removing
option
cards,
or
damage
will
occur!
Also,
you
must
be
very
careful
to
plug
any
option
card
into
its
connector
properly
(pins
aligned).
Mount
the
NPB
‐
LON
option
card
in
either
of
the
option
card
slots
of
the
JACE,
as
needed.
Note
the
J
‐
202
‐
XPR
series
has
only
one
option
card
slot.
Procedure 1
Mounting NPB-LON option card on a JACE.
1.
Remove power
from
the
JACE—see
the
previous
Wait
for
all
LEDs
on
the
unit
to
be
Off.
2.
Remove
the
JACE
cover
or
covers
(J
‐
202
‐
XPR).
For
all
but
the
J
‐
202
‐
XPR,
press
in
the
four
tabs
on
both
ends
of
the
unit,
and
lift
the
cover
off.
Note
If
accessory
modules
are
plugged
into
the
JACE,
you
may
need
to
slide
them
away
from
the
unit
to
get
to
the
cover
tabs.
For
the
J
‐
202
‐
XPR,
first
remove
the
right
cover,
then
the
left
cover,
retaining
the
two
screws
that
secure
each
cover.
1. LON and LonWorks are registered trademarks of the Echelon
Corporation.
Table 1
NPB-LON option description.
Description
Notes / LON Port Assignments
FTT-10A LON
(LonWorks)
adapter with a
2-position
removable
screw-terminal
connector
plug.
Up to 2 LON
®
option cards may be installed
(note that the J-202-XPR series controller
accepts only one option card).
•
If one LON option, it operates as LON1,
regardless of Option slot.
•
If two LON options, LON1 is Option slot 1,
LON2 is Option slot 2.
on page 2 for location of
Option Slots 1 and 2 on a JACE-200/600
.
N
O
L
X
T
X
R
