manualshive.com logo in svg

Tridium JACE-6 Series, Монтаж и подключение

Поделиться
Скачать
Tridium JACE-6 Series Скачать руководство пользователя страница 13

 

Wiring Details

Communications Wiring

JACE-6 Mounting and Wiring Instructions

Part Number 10821

Published: April 19, 2007

13

Note

Prior to connecting cables, provide strain relief for them to prevent damage to the controller. 

Figure 5

JACE-6 bottom side (cover removed).

Ethernet

Two, female 10/100-Mbit Ethernet connections are provided on the JACE-6. These are RJ-45 connectors 
labeled LAN2 and LAN1. Use a standard Ethernet patch cable for connecting to a hub or Ethernet switch. An 
activity LED for each Ethernet port is visible, and are labeled “LAN2” and “LAN1” on the cover.

The factory-default IP address for 

LAN1

 on a JACE-6 is 

192.168.1.12n

, where the last numeral 

n

 in the 

address matches the JACE-6’s serial number, and subnet mask is 

255.255.255.0

. By default, LAN2 on a 

JACE-6 is disabled. Refer to the 

JACE NiagaraAX Install and Startup Guide

 for details on changing IP address.

Note

Typically, you 

only use LAN1

 (primary port), unless you have a specific application for isolating a 

driver’s network traffic to a separate LAN, using LAN2. Do 

not

 use LAN2 as the primary port.

Serial

There are two serial ports on the JACE-6 base board. Each has a UART capable of operation up to 115,200 baud. 
At the bottom of the board (see 

Figure 5

), the left port is an 

RS-232

 port using an DB-9 plug (male) connector. 

To the right of this is a two-wire with shield, isolated 

RS-485

 port, using a screw-terminal connector plug. In 

addition, on the top board (to the right) is a third, standard 

USB

 port.

Note

A green “receive” LED and yellow “transmit” LED are provided for each serial port. These LEDs are 
located on the bottom board, on the 

opposite side

 of the serial connectors (see 

Figure 2

 on page 6). 

These LEDs are labeled on the board (COM1, COM2) and are not visible with the cover on.

RS-232—

An RS-232 serial port using a male DB-9 connector always operates as COM1. You can use standard 

DB-9 serial cables with this port. The JACE-6 is a serial DTE device, such another DTE device (PC, for 
example) requires a “null modem” cable. If connecting the JACE-6 to a DCE device (modem, for example), a 
straight-through cable is used. 

Table 3

 provides standard serial DB-9 pinouts.

Battery in bracket 
(on top of option 
cards, if any)

JACE Battery 
Connector

20 Pin 
Connector

(I/O and Power 

Modules)

Ethernet (RJ-45)

LAN 2 

RS-232

 

(DB-9) 
COM1

Primary

 

Ethernet

 (RJ-45)

LAN 1

 

RS-485

 

(3-pos.)

COM2 

Earth Ground 

Spade Lug

Barrel power 
connector for 

WPM-XXX

.

Option Slot area 
(Slot #1 this side)

s + –

USB

 port 

(future use)

Содержание JACE-6 Series

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды